Siemens Simatic RF382R Scanmode Compact Operating Instructions Download Page 7

 

SIMATIC RF382R Scanmode 

J31069-D0214-U001-A4-7618, 10/2013 

7

 

Field data vertical field  

Table 8-5 

Length of the transmission window at different distances d (reader tag edge) 

d (mm) 

MDS D124 

MDS D160 

MDS D324 

MDS D424 

MDS D460 

155 

130 

155 

150 

120 

10 

150 

125 

150 

145 

115 

20 

140 

110 

140 

135 

105 

30 

130 

100 

130 

120 

90 

 All dimensions in mm 

 

Table 8-6 

Usable field width with dynamic operation (median deviation) 

MDS D124 

MDS D160 

MDS D324 

MDS D424 

MDS D460 

25 

25 

25 

25 

25 

 All dimensions in mm 

 

Table 8-7 

Operating range in mm (S

a

MDS D124 

MDS D160 

MDS D324 

MDS D424 

MDS D460 

10…25 

10…25 

10…25 

10…25 

10…25 

 All dimensions in mm 

 

Table 8-8 

Limit distance in mm (S

g

MDS D124 

MDS D160 

MDS D324 

MDS D424 

MDS D460 

75 

65 

75 

75 

60 

 All dimensions in mm 

 

 

Note 
Tips if the range is too short 
If the range of the antenna is too short, you must check 

 

the power supply/switched-mode power supply (interference) 

 

whether there are monitors or other sources of interference nearby 

 

whether there is metal in the environment 

 

Minimum distance from transponder to transponder (without multitag mode), in mm 
The values are valid at a distance of 20 mm (reader-tag). 

Table 8-9 

Minimum distance transponder 

 

MDS D124 to  
MDS D124 

MDS D160 to  
MDS D160 

MDS D324 to  
MDS D324 

MDS D424 to  
MDS D424 

MDS D460 to  

MDS D460 

Horizontal main 

field 

100 

100 

100 

100 

100 

Vertical main field  150 

120 

150 

180 

120 

 
The minimum distance can be undershot in multitag mode. 

Summary of Contents for Simatic RF382R Scanmode



















Reviews: