background image

Table of contents

1

Introduction...................................................................................................................................................5

2

Safety notices ...............................................................................................................................................9

3

Recommendations on network security......................................................................................................11

4

Description of the device ............................................................................................................................17
4.1

Product overview....................................................................................................................17

4.2

Device views ..........................................................................................................................20

4.2.1

SCALANCE XB208 ................................................................................................................20

4.2.2

SCALANCE XB205-3.............................................................................................................21

4.2.3

SCALANCE XB213-3.............................................................................................................22

4.3

RESET button ........................................................................................................................23

4.4

LED display ............................................................................................................................25

5

Installation ..................................................................................................................................................27
5.1

Safety notices for installation .................................................................................................27

5.2

Mounting on DIN rails.............................................................................................................30

6

Connecting up ............................................................................................................................................33
6.1

Safety when connecting up ....................................................................................................33

6.2

Industrial Ethernet ..................................................................................................................35

6.2.1

Electrical.................................................................................................................................35

6.2.2

Optical ....................................................................................................................................37

6.3

Wiring rules ............................................................................................................................38

6.4

Power supply..........................................................................................................................39

6.5

Serial interface .......................................................................................................................41

6.6

Functional ground ..................................................................................................................43

7

Upkeep and maintenance...........................................................................................................................45
7.1

Downloading new firmware using TFTP without WBM and CLI.............................................45

7.2

Restoring the factory settings.................................................................................................47

8

Technical specifications..............................................................................................................................49
8.1

Technical specifications of the SCALANCE XB208 ...............................................................49

8.2

Technical specifications of the SCALANCE XB205-3 (SC) ...................................................50

8.3

Technical specifications of the SCALANCE XB205-3LD (SC)...............................................52

8.4

Technical specifications of the SCALANCE XB205-3............................................................54

8.5

Technical specifications of the SCALANCE XB216 ...............................................................56

8.6

Technical specifications of the SCALANCE XB213-3 (SC) ...................................................57

SCALANCE XB-200

Operating Instructions, 03/2020, C79000-G8976-C359-09

3

Summary of Contents for SIMATIC NET SCALANCE XB-200 Series















































































Reviews: