Siemens SIMATIC NET CP 1628 Operating Instructions Manual Download Page 19

Page: 19 / 22

CP 1628
Operating Instructions, 06/2021, C79000-G8976-C280-09

Technical specifications

CP 1628

The following technical specifications apply to the CP 1628 communications processor:

Data transfer

Transmission speed

•

10/100 Mbps (half/full duplex)

•

1000 Mbps (full duplex)

Interfaces

Connection to 10BaseT/100BaseTx/ 1000BaseT

RJ-45 ports (two)

Connector for PG/PC

PCI Express x1; can also be operated in x4, x8 or x16 slots

Power

PCIe power supply

3.3 VDC and 12 VDC

External power supply

Rated voltage

12 to 24 VDC

Limit voltages

Min. 10.5 VDC

Max. 32 VDC

Current consumption

PCIe power at 3.3 VDC

max. 0.85 A

PCIe power at 12 VDC

max. 0.4 A

Permitted ambient conditions

Operating temperature

+5 to +55 °C

Transportation/storage temperature

-20 to +60 °C

Summary of Contents for SIMATIC NET CP 1628























Search results

Summary of Contents for SIMATIC NET CP 1628

Reviews:

Related manuals for SIMATIC NET CP 1628

Brands by name

Popular brands

Siemens SIMATIC NET CP 1628, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC NET CP 1628

Reviews:

Related manuals for SIMATIC NET CP 1628

Brands by name

Popular brands