Siemens SIMATIC IPC677E Operating Instructions Manual Download

Page: 92 / 158

Maintaining and servicing your device

7.4 Removing and installing hardware

SIMATIC IPC677E

Operating Instructions, 04/2019, A5E45117996-AA

7.4

Removing and installing hardware

7.4.1

Replacing device fans

Requirement

●

The device is disconnected from the mains and all connecting cables have been

removed.

●

The device is open, see important information regarding this under Opening the Device

(Page 71).

●

An original spare part, that is a fan of the same type, see information under Accessories:

Hardware (Page 22).

Procedure - Removal

Remove the two screws

①

and remove the air guide pulling it up vertically.

Loosen the plastic rivets.

Summary of Contents for SIMATIC IPC677E































































































































































Search results

Summary of Contents for SIMATIC IPC677E

Reviews:

Related manuals for SIMATIC IPC677E

Brands by name

Popular brands

Siemens SIMATIC IPC677E, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC IPC677E

Reviews:

Related manuals for SIMATIC IPC677E

Brands by name

Popular brands