Siemens SIMATIC IPC677E Operating Instructions Manual Download

Page: 71 / 158

SIMATIC IPC677E
Operating Instructions, 04/2019, A5E45117996-AA

Expanding the device and assigning device

parameters

6.1

Opening the Device

WARNING

Risk due to unauthorized opening and improper repairs or expansions
Improper procedure when carrying out expansions may result in substantial damage to

equipment or endanger the user.
If you install or exchange system expansions and damage your device, the warranty

becomes void.

•

For this reason, please observe the information in "Notes on device and system

extensions (Page 31)".

WARNING

Malfunctions and electric shock
Improper intervention in the device endangers operational reliability and may damage the

device.
The results can be personal injuries and damage to the plant.
Take the following precautions:

•

Always disconnect the power plug before you open the device.

•

Close the device after every intervention.

NOTICE
Electrostatic-sensitive components
The device contains electronic components which may be destroyed by electrostatic

charge.
Take suitable precautionary measures when you open the device.

Summary of Contents for SIMATIC IPC677E































































































































































Search results

Summary of Contents for SIMATIC IPC677E

Reviews:

Related manuals for SIMATIC IPC677E

Brands by name

Popular brands

Siemens SIMATIC IPC677E, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC IPC677E

Reviews:

Related manuals for SIMATIC IPC677E

Brands by name

Popular brands