Siemens SIMATIC IOT Operating Instructions Manual Download Page 50

Page: 50 / 64

Technical specifications

7.5 Hardware descriptions

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 10/2016, A5E37656492-AB

Component/interface Description / inscription

Meaning, comment

LEDs

PWR

Power (green)

Micro SD card active (green)

USB

USB Power (5 V) is available (green)

OverCurrent (red)

H5/H6 *

USER

User LED (green/red*/orange*), programmable

RESET

For a reset of the CPU

USER

Status can be queried with programming

Ethernet1

Ethernet2 ready for PoE

X30, X31

COM D-Sub9

X60

USB A

X61

USB B Micro

X14

UART Debug

X40

Battery-Con

X50

µSD slot

X11, X13

Arduino, 8-pin (2x)

X10

Arduino, 10-pin

X12

Arduino, 6-pin

X15

ICSP

Part of Arduino Interface

X16

JTAG Internal

X80

Power supply

X18

Jumper 3 pin SMD

Jumper defines IO voltage for Arduino shield:

•

Jumper on pins 1-2: 5 V

•

Jumper on pins 2-3: 3.3 V

X100

MiniPCIe Con.

X101

Latch

X82

VIN Separation (power

supply, 9...36 V DC)

Jumper defines VIN connection to the Arduino

shield:

•

Jumper on pins 1-2: VIN is connected to the

Arduino shield

•

Jumper on pins 2-3: VIN is not connected to

the Arduino shield

* The LED H6 is only available with SIMATIC IOT2040.

Summary of Contents for SIMATIC IOT

































































Search results

Summary of Contents for SIMATIC IOT

Reviews:

Related manuals for SIMATIC IOT

Brands by name

Popular brands

Siemens SIMATIC IOT, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC IOT

Reviews:

Related manuals for SIMATIC IOT

Brands by name

Popular brands