manualshive.com logo in svg

Siemens SICAM A8000 Series, Manual

Share
Download
Siemens SICAM A8000 Series Manual Download Page 19

Introduction 

SICAM A8000 Series, SICAM I/O Modules 

Unrestricted   

19 

DC8-012-2.06, Edition 09.2019 

1.3 

Commissioning 

1.3.1 

Mounting 

Precondition for the mounting of the SICAM I/O Modules is, that the SICAM A8000 System 
which should be expanded, is already mounted on the DIN rail. Then you can mount the bus 
connector which is delivered with the SICAM I/O Module on the DIN rail and press it into the 
connector of the Master Module (in case of CP-8000 in the connector of the coupling module). 
Afterwards you can plug the SICAM I/O Module on the bus connector. 

 

Warning 

The removal and attachment of energized modules is not allowed.  
For modules that operate with voltages >60 V, care must be taken that manipulation on the peripheral 
connectors may only be carried out in a de-energized state.  
The display (LCD, LED) of the modules do not grant a guarantee that the peripheral connectors are de-
energized. 

 

 

Note 

For details about the mounting refer to the manual 

SICAM A8000 Series CP-8000, CP-8021, CP-8022.

 

 

 

Caution 

Bus communication is system-internal only. It is not allowed to modify the bus connector. 

The devices must be powered by a SICAM A8000 power supply only. For USA and Canada: Use a UL 
listed SICAM A8000 power supply. 

1.3.2 

Electrical Connection 

Check the adherence of the specified limit values. 

Connect the process-devices to the screw terminals. Cabinet-internal wiring is preferably 
carried out with plastic-insulated cables according to DIN VDE 298 T4 2/89. Types: H05V-
K/H05V2-K (0.5…1 mm²) or H07V-K/H07V2-K (1.5…2.5 mm²). Use only copper wires. 

Due to the power dissipation in the device there is a higher temperature on the terminals than 
the device ambient temperature. This increase is maximum 15°C with full load. For this 
reason, the isolation of the wires must withstand a higher temperature than the device 
environment temperature. 

Example: 

Max. ambient 
temperature 

Max. temperature 
on the terminal 

Appropriate wire type 

55 °C 

70 °C 

H05V-K, H07V-K 

70 °C 

85 °C 

H05V2-K, H07V2-K 

Conductor size, ampacity and temperature rating per the National Electrical Code. 

 

 

Note 

The SICAM I/O modules are switched ON and OFF with the SICAM A8000 master module. 

 

Summary of Contents for SICAM A8000 Series



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands