Siemens SENTRON Series Product Manual Download Page 37

Page: 37 / 40

Expansion module I(N), I(Diff), analog
Manual, 04/2017, L1V30408520AG-01

Index

Ambient conditions

Technical specifications, 34

Approvals

Technical specifications, 34

Calibration

Service and maintenance, 29

Connection elements

Technical specifications, 32

Degree of protection and protection class

Technical specifications, 33

Device configuration

Technical specifications, 31

Diagnostic LED

Design, (Description)

Dimensions and weight

Technical specifications, 33

Disposal

Service and maintenance, 30

Example connections

Connections, (Connection)

Firmware update

Service and maintenance, 29

I5 connection

Design, (Description)

I6 connection

Design, (Description)

IN connection

Design, (Description)

Installation location

Installation, 15

Installation steps

Installation, 15

Latest information

Introduction, 7

Measuring accuracy

Technical specifications, 32

Measuring inputs

Technical specifications, 31

Performance features

Description, 11

Reading out from PAC device

Reading out measured values, (Commissioning)

Requirements

Commissioning, 23

Safety information

Introduction, 9

Scope of delivery

Introduction, 7

Setting parameters on the PAC device

Setting the expansion module

parameters, (Commissioning)

Setting the ADC parameters

Setting the expansion module

parameters, (Commissioning)

Setting the CT parameters

Setting the expansion module

parameters, (Commissioning)

Summary of Contents for SENTRON Series









































Search results

Summary of Contents for SENTRON Series

Reviews:

Related manuals for SENTRON Series

Brands by name

Popular brands

Siemens SENTRON Series, Product Manual

Search results

Summary of Contents for SENTRON Series

Reviews:

Related manuals for SENTRON Series

Brands by name

Popular brands