background image

5

 3

Montage

Die erforderlichen Montageschritte sind nachfolgend für eine KSV 
der Baugröße I, 3-polig mit einem Bemessungsstrom von 1000 A 
erläutert. Sie treffen prinzipiell auch für alle anderen Baugrößen und 
Ausführungen zu.

Die Anpassung an einen höheren Bemessungsstrom erfolgt mit 
Adapterplatten auf den Anschlussschienen, wodurch deren Quer-
schnitt entsprechend erhöht und das Einfahren der KSV in die grö-
ßeren Lamellenkontakte möglich wird.

Die hinter einer Teilebezeichnung aufgeführte Nummer entspricht 
der Positionsnummer in der Gesamtdarstellung auf 

q

Seite 2

.

 3.1

Konfigurieren

 3.1.1

Konfiguration 1 

Obere Anschlüsse kurzgeschlossen und geerdet.

Obere Anschlussschienen montieren

Obere Anschlussschiene (2) in hintere Gehäusehälfte (1.1) 

einsetzen

Einlegemutter (2a) einlegen

Anschlussschiene (2) mit Schraube (2b) und 

Spannscheibe (2c) von hinten befestigen

Schraube festziehen und restliche Anschlussschienen oben 

in gleicher Weise montieren

1

2

10 Nm

Gr. / Size

5

3

4

 3

Assembly

In the following, the necessary assembly steps will be explained for 
a SCD, size I, 3-pole with a rated current of 1000 A. These steps 
are principally the same for all other sizes and versions.

Adjustment to a higher rated current is carried out via adapter plates 
on the connecting bars, which increase their respective cross sec-
tion and enable insertion of the SCD into the larger laminated con-
tacts.

The number listed behind a component designation corresponds to 
the position number in the overall diagram on 

q

page 2

 3.1

Configuring

 3.1.1

Configuration 1

The upper connections are short-circuited and earthed.

Mounting the upper connecting bars

Insert the upper connecting bar (2) into the rear half of the 

housing (1.1)

Insert the square nut (2a)

Fasten the connecting bar (2) with the screw (2b) and the 

spring washer (2c) from the back

Tighten the screw and mount the remaining connecting bars 

in the same manner

Summary of Contents for Sentron 3ZX1812-0WL90-0AA0























Reviews: