background image

Technical Specifications
5.3 Operating Environment

5.3

Operating Environment

The RUGGEDCOM RX1510 is rated to operate under the following environmental

conditions.

NOTICE

Temperature limits for select line modules may differ from that which can be with-

stood by the RUGGEDCOM RX1510. Make sure the selected modules are rated for

the expected environmental conditions before deployment. For more information,

refer to the 

 RUGGEDCOM RX1510 Series Modules Catalog

.

Ambient Operating Tempera-

ture

a

 

b

 

c

-40 to 85 °C (-40 to 185 °F)

Ambient Storage Temperature

-40 to 85 °C (-40 to 185 °F)

Ambient Relative Humidity

d

5% to 95%

Maximum Altitude

2000 m (6562 ft)

a

Maximum ambient operating temperature is 70 °C (158 °F) when the device is installed along with

Underwriter Laboratories (UL) listed devices.

b

Measured from a 30 cm (12 in) radius surrounding the center of the enclosure.

c

Operating temperature may vary based on the limitations of installed SFPs. Refer to the 

 RUGGEDCOM

SFP Transceivers Catalog

 for SFP temperature ratings.

d

Non-condensing.

5.4

Mechanical Specifications

Weight

Approximately 5.0 kg (11 lb)

Ingress Protection

IP30

Enclosure

Aluminum

5.5

Dimension Drawings

Note

All dimensions are in millimeters, unless otherwise stated.

44

RUGGEDCOM RX1510

Installation Manual, 12/2019, C79000-G8976-1055-16

Summary of Contents for RUGGEDCOM RX1510































































Reviews: