background image

4/7 

Siemens 

Master room unit QAX850 

 

CE1N2722en 

Building Technologies  

 

28.08.2007 

No. Parameter 

Range 

P06 

RV ON in heat or cool mode 

Heat/Cool 

P07 

Fan run ON after heat output turns Off 

0…300 s 

P08 

Fan run ON after cool output turns Off 

0…300 s 

P09 

FCU flush pipe time 

120…600 s 

P10 

Zone Heat / Cool Inhibit 

Heat/Cool/No 

P11 

Water temp. heat mode changeover 

22…32 °C 

P12 

Water temp. cool mode changeover 

10…21 °C 

P13 

Fan auto-speed high range  

H:80…100 % 

P14 

Fan auto-speed medium range 

M:30…75 % 

P15 

Fan auto-speed low range 

L:1…15 % 

P16 

Window contact  

NO/NC 

P17 

2-p or 3-p control selection 

2-p/3-p 

P18 

P-band in heat mode /Switching differential 

0.5…10 K 

P19 

P-band in cool mode /Switching differential 

0.5…10 K 

P20 

Integration time 

0…60.0 min in 
0.5 min steps 

P21 

3-p valve actuator running time 

50…300 s 

P22 

Zone capacity weight 

None 
Small  
Medium  
Large  

P23 

Ventilation in dead zone 

Off, H/C, C only 

 
QAX850 internal sensor can be replaced by connecting an external NTC resistor 
sensor (QAA32 or QAH11) to the RRV controller B1 input. In this case the QAX850 
automatically recognizes and displays the external sensor value.  

Mounting and installation notes 

The QAX850 should be mounted in a location where the air temperature can be 
measured as accurately as possible without getting adversely affected by direct solar 
radiation or other heating or cooling sources. There is no need to consider air 
temperature conditions if external sensor is connected to the RRV controller. In this 
case the QAX850 would serve as a master control unit only. 

 

  Mounting height is about 1.5 m above the floor. 

  QAX850 must not be located in the direct path of air conditioning air flow. 

  The unit can be fitted to a recessed conduit box. 

  The specified ambient conditions must be complied with.  

  Only authorized staff may disconnect the QAX850 unit from base plate. 

  Do not mount in recesses, shelves, behind curtains or doors. 

  Refer to Mounting Instructions M2721 included in packaging box. 

When mounting the unit, fix the base-plate first and then make the electrical 
connections. To avoid any damage during construction works only install QAX850 unit 

Internal sensor 

Summary of Contents for QAX850








Reviews: