Siemens PS-5N7 Installation Instructions Manual Download Page 1

P/N 315-092729-13

Fire Safety

OPERATION

The Model PS-5N7 from Siemens Building
Technologies, Inc. permits remote mounting
of the MXL annunciator modules MKB-1,
MKB-2, and RCC-1/-1F. In addition, when the
PS-5N7 is used with a PIM-1, it provides an
interface for a remote printer that can be
supervised or unsupervised. Each PS-5N7
occupies one network node.

INSTALLATION

Mounting

The PS-5N7 can be used in an MME-3, MSE-2,
or an RCC-1/-1F enclosure. Mount the PS-5N7
in the following enclosures as described below
(See the Note at the top of page 2 if using a
PIM-1):

Figure 1

PS-5N7 Wiring Diagram in MME-3 or MSE-2 (Without a PIM-1)

1. MME-3—Install in the upper right-hand

corner (See Figure 1).

2. MSE-2—Install in the upper right-hand

corner (See Figure 1).

3. RCC-1/-1F—Install in the lower right-

hand corner (See Figure 2).

Note:  In a special application which is

described on page 7, the PS-5N7
can be used as a source of
power in a remote extender
enclosure used to house extra
VSMs/VLMs/VFMs.

Installation Instructions

Model PS-5N7
Network Interface / 5V Power Supply

Siemens Building Technologies, Inc.
8 Fernwood Road
Florham Park, New Jersey 07932

Siemens Building Technologies, Ltd.
2 Kenview Boulevard
Brampton, Ontario  L6T 5E4 CN

Summary of Contents for PS-5N7









Reviews: