manualshive.com logo in svg

Siemens MAMMOMAT Novation SP, Installation Instructions Manual, Page: 28 / 36

Share
Download
Siemens MAMMOMAT Novation SP Installation Instructions Manual Download Page 28

28

Installing the system components

MAMMOMAT Novation

SPB7-250.812.03.02.02

Siemens AG

08.04

CS SD 24

Page 28 of 36

Medical Solutions

Bolting the stand/radiation shield to the floor

0

Should a permanent fastening to the floor be required due to local regulations (for exam-
ple in areas subject to earthquakes) or due to the quality of the floor covering, the 
stand/radiation shield can be bolted to the floor by means of safety dowels and screws. 
When bolting the stand/radiation shield to the floor, the fixing screws shall pass through 
the hollow levelling screws 

(1/Fig. 20 / p. 28)

and

(1/Fig. 21 / p. 29)

.

NOTE

Cable lead-in from the floor only on-the-floor calbe conduits in-
cluded in the shipment cannot be used. For on-the-floor cable co-
duits 

(Factory adjustments / p. 8)(Protective measures / p. 9)

Fig. 20: Base plate for the stand

Pos. 1

screws

Pos. 2

Cable lead-in from the floor left or right. Obtain cable conduits on site.

Pos. 3

Slots for cable lead-in

Summary of Contents for MAMMOMAT Novation SP





































Reviews:

No comments