Siemens M20 Terminal Technical Description Download Page 70 | Manualshive

Page: 70 / 234

background image

AT command interface

Version 8 dated 15.03.00

70

Siemens Information and Communication Products

AT+COPS

Operator selection

Test command

AT+COPS=?

Response

TA returns a list of quadruplets, each representing an operator present in the network. Any of the
formats may be unavailable and should then be an empty field. The list of operators shall be in the
following order: home network, networks referenced in SIM, and other networks.

+COPS: [<stat>, long alphanumeric <oper>, numeric <oper>)s] [,(list of supported <mode>s),
(list of supported <format>s)] OK

If error is related to ME functionality:

+CME ERROR: <err>

Parameter

see set command

Read command

AT+COPS?

Response

TA returns the current mode and the currently selected operator. If no operator is selected, <for-
mat> and <oper> are omitted.

+COPS: <mode>[, <format>, <oper>] OK

Parameter

see set command

Set command

AT+COPS =

<mode>

[, <format>[,
<oper>]]

Response

TA forces an attempt to select and register the GSM network operator. If the selected operator is
not available, no other operator shall be selected (except <mode>=4). The selected operator name
format shall apply to further read commands (+COPS?) also.

Parameters used with the set command are stored in the non-volatile memory.

e.g. using AT+COPS=2 to book out of the net, causes the system to NOT automatically book in
after the next power-on. AT+COPS=0/1 is needed to register into the network.

OK

If error is related to ME functionality:

+CME ERROR: <err>

Parameter

<stat>

0

unknown

1

operator available

2

operator current

3

operator forbidden

<oper>

operator in format as per <format>

<mode>

0

automatic mode; <oper> field is ignored

1

manual operator selection; <oper> field shall be present

2

manual deregister from network and remain unregistered until mode 0, 1, 4 is
selected

3

set only <format> (for read command +COPS?)

4

automatic, manual selected; if manual selection fails, automatic mode (<mo-
de>=0) is entered

<format>

0

long format alphanumeric <oper>; can be up to 16 character long

1

short format alphanumeric

2

numeric <oper>; GSM Location Area Identification number

Reference

GSM 07.07

Note

«
...
68
69
70
71
72
...
»

Summary of Contents for M20 Terminal











































































































































































































































Reviews:

No comments

Related manuals for M20 Terminal

Brand: Yamaha Pages: 7

RailKing RKS SD70ACE

Brand: M.T.H. Pages: 12

Brand: Eurotronic Pages: 4

Brand: ACME motori Pages: 23

Brand: Just Motion Control Pages: 21

PS01-37x120F-HP-SSC-R/ FC

Brand: LinMot Pages: 40

2232***BX4 series

Brand: Faulhaber Pages: 60

Brand: A'OK Pages: 7

Brand: A'OK Pages: 11

Brand: Valmet Pages: 134

Brand: Tardis Pages: 3

Brand: Honda Pages: 33

Brand: Yamaha Pages: 96

Brand: Sailrite Pages: 4

Brand: Moki Pages: 3

Brand: BREL Pages: 5

Brand: DANA Pages: 2

INTERNATIONAL DT 466

Brand: Navistar Pages: 520

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands