Siemens M20 Terminal Technical Description Download Page 68

Page: 68 / 234

AT command interface

Version 8 dated 15.03.00

Siemens Information and Communication Products

AT+CLIR

Calling line identification restriction

Test command

AT+CLIR=?

Response

+CLIR: (list of supported <n>s) OK

Parameter

see set command

Read command

AT+CLIR?

Response

+CLIR: <n>, <m> OK

If error is related to ME functionality:

+CME ERROR: <err>

Parameter

see set command

Set command

AT+CLIR=[<n>]

Response

TA restricts or enables the presentation of the CLI to the called party when originating a call.

The command overrides the CLIR subscription (default is restricted or allowed) when temporary
mode is provisioned as a default adjustment for all following outgoing calls. This adjustment can
be revoked by using the opposite command.

Parameter

<n>

(parameter sets the adjustment for outgoing calls):

presentation indicator is used according to the subscription of the CLIR ser-
vice

CLIR invocation

CLIR suppression

<m>

(parameter shows the subscriber CLIR service status in the network):

CLIR not provisioned

CLIR provisioned in permanent mode

unknown (e.g. no network, etc.)

CLIR temporary mode presentation restricted

CLIR temporary mode presentation allowed

Reference

GSM 07.07

Note

If other party sets CLIR then the M20 replies with +CLIP: number presentation restricted.

AT+CMEE

Report mobile equipment error

Test command

AT+CMEE=?

Response

+CMEE: (list of supported <n>s) OK

Parameter

see set command

Read command

AT+CMEE?

Response

+CMEE: <n> OK

Parameter

see set command

Set command

AT+CMEE=<n>

Response

TA disables or enables the use of result code +CME ERROR: <err> as an indication of an error
relating to ME functionality.

Parameter

<n>

disable result code

enable result code and use numeric values

enable result code and use verbose values

Reference

GSM 07.07

Note

The possible error result codes are listed in chapter

5.9.2

Summary of Contents for M20 Terminal











































































































































































































































Search results

Summary of Contents for M20 Terminal

Reviews:

Related manuals for M20 Terminal

Brands by name

Popular brands

Siemens M20 Terminal, Technical Description

Search results

Summary of Contents for M20 Terminal

Reviews:

Related manuals for M20 Terminal

Brands by name

Popular brands