Siemens Insys 56k Operating Manual Download Page 70

Page: 70 / 84

S- Registry

Pocket Modem 56k

Dezember 05

S91*

Transmit Level:

The value for the transmit level of the modem is stored in the S91 registry. The

value can be set between 0 and 15. The connection can in some cases be improved
by decreasing the transmit level.
S91=0

Transmit level –1 dBm

S91=15

Transmit level -26 dBm

Note:

The range and the default value depend on the country settings
(

AT+GCI

S95*

Result code

Bit Meaning

Bit 0

CONNECT message with line speed

Bit 1

CONNECT/ARO message for error corrected connection

Bit 2

CARRIER messages enabled (messages 40 – 47)

Bit 3

PROTOCOL messages enabled (messages 70 – 80)

Bit 4

Reserved

Bit 5

COMPRESSION message enabled (messages 66 - 69)

Bit 6

Reserved

Bit 7

Reserved

Summary of Contents for Insys 56k





















































































Search results

Summary of Contents for Insys 56k

Reviews:

Related manuals for Insys 56k

Brands by name

Popular brands

Siemens Insys 56k, Operating Manual

Search results

Summary of Contents for Insys 56k

Reviews:

Related manuals for Insys 56k

Brands by name

Popular brands