Siemens i-3 User Manual Download Page 39

Page: 39 / 80

Appendix C

Modbus Coils, Discrete Inputs, Input Registers & Holding Registers Address Tables

Holding Registers

Function
code

Modbus base 0
address

Modbus
5 digit address

Value
(Read/Write*)

Description

Note

364

40365

Output Group (Zone) deﬁ nition 109

365

40366

Output Group (Zone) deﬁ nition 110

366

40367

Output Group (Zone) deﬁ nition 111

367

40368

Output Group (Zone) deﬁ nition 112

368

40369

Output Group (Zone) deﬁ nition 113

369

40370

Output Group (Zone) deﬁ nition 114

370

40371

Output Group (Zone) deﬁ nition 115

371

40372

Output Group (Zone) deﬁ nition 116

372

40373

Output Group (Zone) deﬁ nition 117

373

40374

Output Group (Zone) deﬁ nition 118

374

40375

Output Group (Zone) deﬁ nition 119

375

40376

Output Group (Zone) deﬁ nition 120

376

40377

Output Group (Zone) deﬁ nition 121

377

40378

Output Group (Zone) deﬁ nition 122

378

40379

Output Group (Zone) deﬁ nition 123

379

40380

Output Group (Zone) deﬁ nition 124

380

40281

Output Group (Zone) deﬁ nition 125
(see “Output

381-776

...

Reserved

777

40778

BlinkTime (0-15000 s) // time in seconds for blinking
the lights (default 300) Note: It is advisable to select
more than 60 seconds as Blink time

778

40779

BlinkCycle (0-15000 s) // time in seconds for the
blinking off/on cycle (i.e., frequency of blinking)
(default 60). Note: It is advisable to select 30 or
more seconds as blink cycle.

779

40780

BlinkOffTime (0-255 s) // time in seconds that the
lights are turned off in each cycle (default 1)

780

40781

Reserved

781

40782

Time in minutes to check for the
communication loss. (See the section
Communication Loss)

782-1023

...

Reserved

1024

41025

Bit 15

Status, 0 - Open, 1 - Closed

SIPOD 1 Report

Bit 8-14

Other ﬂ ags

Bit 0-7

Version

1025

41026

Timestamp - Minutes

1026

41027

Timestamp - Ticks (ms)

1027

41028

Total “Open” operations performed

1028

41029

Total “Close” operations performed

1029

41030

Total Failures (to open or close)

1030

41031

Total Garbled messages

1031

41032

Bit 8-15

MaxOpensPerMinute

Bit 0-7

MinTimeBetweenOpens (ms)

1032

41033

Bit 8-15

MaxClosesPerMinute

Bit 0-7

MinTimeBetweenCloses (ms)

1033

41034

Bit 8-15

OpenPulseWidth (ms)

Bit 0-7

CloseCompleteTime

1034

41035

Bit 8-15

ClosePulseWidth

Bit 0-7

CloseCompleteTime

1035

41036

Bit 15

Status - First pole

0-Open,1-Closed

Bit 14

Status - 2nd pole, if Two/Three Pole

0-Open,1-Closed

Bit 13

Status - 3rd pole, if Three Pole

0-Open,1-Closed

SIPOD 1 Repor

Summary of Contents for i-3

















































































Search results

Summary of Contents for i-3

Reviews:

Related manuals for i-3

Brands by name

Popular brands

Siemens i-3, User Manual

Search results

Summary of Contents for i-3

Reviews:

Related manuals for i-3

Brands by name

Popular brands