en
Basic operation
14
‒
Ventilate the kitchen while the appliance is heat-
ing.
a
When the time has elapsed, a signal tone sounds. A
message appears on the display confirming that the
operation has finished.
10.
Press to switch the appliance off.
11.
Once the appliance has cooled down, clean the
smooth surfaces in the cooking compartment with a
detergent solution and a dish cloth.
12.
Clean the accessories thoroughly using a detergent
solution and a dish cloth or soft brush.
13.
Dry the appliance.
"After using steam operation", Page 19
Note:
Following a power cut, the calibrated settings are
retained.
To adjust the appliance to a new installation location
after moving house, reset the basic settings to the fact-
ory settings. Restart the calibration process.
8 Basic operation
8.1 Switching on the appliance
▶
Press to switch the appliance on.
a
The display shows the menu.
8.2 Switching off the appliance
Switch your appliance off when you are not using it.
The appliance automatically switches itself off if it is not
used for a certain period of time.
▶
Press to switch the appliance off.
a
The appliance switches off. Any functions currently
in progress are cancelled.
a
The time or residual heat indicator appears on the
display.
8.3 Starting the operation
You must start each operation.
ATTENTION!
If there is water on the cooking compartment floor
when operating the appliance at temperatures above
120 °C, this will damage the enamel.
▶
Do not use the appliance if there is water on the
cooking compartment floor.
▶
Wipe away any water on the cooking compartment
floor before operation.
▶
Use "Start" to start the operation.
a
The settings appear on the display.
8.4 Interrupting the operation
You can interrupt the operation and then continue
again.
1.
To interrupt the operation, press "Stop".
2.
To continue the operation, press "Start".
8.5 Setting an operating mode
After you have switched on the appliance, the menu
appears on the display.
1.
To scroll through the various selection options,
swipe to the left or right on the display.
2.
To select a function, press the corresponding tile.
a
Depending on the function, possible adjustment val-
ues or other tiles are available for selection.
3.
If required, press on another tile.
4.
To change the adjustment values:
‒
Swipe over the blue adjustment line or push the
adjustment line to the appropriate point.
‒
Or press and enter the value directly via the
number field that appears.
5.
Use "Start" to start the operation.
6.
If the operation is ended:
‒
If required, you can select other settings and re-
start the operation.
‒
When the food is ready, use to switch the ap-
pliance off.
Tip:
You can save your settings as "Favourites" and
use these again.
8.6 Setting the type of heating and the
temperature
1.
Press "Types of heating".
2.
Press the type of heating that you want to use.
3.
Set the temperature using the adjustment line or dir-
ectly via the number field .
If required, you can implement additional settings:
– →
– →
"Time-setting options", Page 15
– →
– →
4.
Use "Start" to start the operation.
a
The appliance starts heating.
a
The adjustment values and how long the appliance
has already been in operation are shown on the dis-
play.
5.
When the food is ready, use to switch the appli-
ance off.
Note:
The most suitable type of heating for your food
can be found in the type of heating description.
Changing the type of heating
When you change the type of heating, the other set-
tings are also reset.
1.
Press "Stop".
2.
Press
.
3.
Press the type of heating that you want to use.
4.
Reset the operation and use "Start" to start.
Changing the temperature
Once the operation has started, you can change the
temperature at any time.
1.
Press the temperature.
2.
Change the temperature using the adjustment line
or enter it directly via the number field .
3.
Press "Apply".
