Siemens HS658GE 7B Series, Instruction Manual

Page: 14 / 64

en
Before using for the first time
14
Initial use
After connecting the appliance to the power or following
a power cut, the settings for initial use are shown in the
display.
Note:
You can change these settings at any time in the
basic settings.
~
"Basic settings" on page 21
Setting the language
German is the preset language.
1.
Use the rotary selector to select the required
language.
2.
Touch the
Æ
arrow.
The next setting appears.
Setting the clock
The time starts at 12:00.
1.
Use the rotary selector to set the current time.
2.
Touch the
Æ
arrow
Setting the date
The default date is 1.1.2014.
1.
Always touch the
Æ
arrow to move to the next
setting.
2.
Use the rotary selector to set the current day, month
and year.
Setting the water hardness
The default water hardness setting is "very hard".
Change this setting if your water is softer. You can ask
your water supplier about the water hardness level.
1.
Set the hardness using the rotary selector.
2.
Touch the
Æ
arrow.
A message appears on the display confirming that
the initial use has been completed.
With HomeConnect
1.
Touch "Set using the assistant".
2.
Further instructions can be found in section
~
"Home Connect" on page 23
Calibrating the appliance and cleaning the
cooking compartment
The boiling point of water depends on the air pressure.
During calibration, the appliance self-adjusts to the
pressure ratio at the installation location. This will
happen automatically the first time steam-assisted
cooking is used. This produces a lot of steam.
Preparing the appliance for calibration
1.
Remove the accessories from the cooking
compartment.
2.
Remove any leftover packaging, such as polystyrene
pellets, from the cooking compartment.
3.
Before calibrating the appliance, wipe the smooth
surfaces in the cooking compartment with a soft,
damp cloth.
Calibrating the appliance and cleaning the cooking
compartment
Notes
■
Calibration cannot be started until the cooking
compartment is cold (room temperature).
■
Do not open the appliance door while calibration is
in progress, as this will abort the calibration process.
1.
Press the on/off button to switch on the appliance.
2.
Fill the water tank.
~
"Filling the water tank"
on page 18
3.
Set the specified type of heating, temperature and
duration for the calibration, then start the appliance.
~
"FullSteam – Steam cooking" on page 16
4.
Heat up the appliance following calibration.
Caution!
Enamel damage
Do not use the appliance if there is water on the
cooking compartment floor. Before using the
appliance, wipe away the water from the cooking
compartment floor.
5.
Dry the cooking compartment floor.
6.
Set the specified type of heating and temperature for
heating, then start the appliance.
7.
Keep the kitchen ventilated while the appliance is
heating.
8.
Stop the appliance once the specified time has
elapsed. Press the on/off button to switch off the
appliance.
9.
Wait for the cooking compartment to cool down.
10.
Clean the smooth surfaces with soapy water and a
dish cloth.
11.
Empty the water tank and dry the cooking
compartment.
~
"After every steam operation"
on page 19
Notes
■
When relocating the appliance, restore its factory
settings once it is installed so that it can adapt to its
new location. Repeat the procedures for initial start-
up and calibration.
■
The appliance retains the calibration settings, even
in the event of a power cut or disconnection from the
mains. Calibration does not need to be repeated.
Water hardness range Setting
0 0 softened
1 (up to 1.3 mmol/l) 1 soft
2 (1.3 - 2.5 mmol/l) 2 medium
3 (2.5 - 3.8 mmol/l) 3 hard
4 (above 3.8 mmol/l) 4 very hard
Calibration
Type of heating
Steam P
Temperature 100 °C
Cooking time 30 minutes
Heating up
Type of heating
4D hot air :
Temperature Maximum
Cooking time 30 minutes