Siemens Flender KMP Series Assembly And Operating Instructions Manual Download Page 69

Page: 69 / 84

69 / 84

BA 9142 en 02/2015

Faults

Remedy

Possible causes

The oil foams.

Water in oil.

Oil too old (defoaming agent used
up).

Unsuitable oils mixed up.

Examine oil.
Change oil if necessary.

Water in oil.

Cooler leaky.

Water condensing.

Replace cooler.

Change oil.

Reduce water content by heating the
oil.

Fault in oil-supply system.

Observe operating instructions
for the oil-supply system.

NOTICE

Property damage

Damage can be caused to the gear unit if low-quality operating oils are used.
The quality of the oil used must meet the requirements of the separately enclosed BA 7300 instructions
manual.

Summary of Contents for Flender KMP Series





















































































Search results

Summary of Contents for Flender KMP Series

Reviews:

Related manuals for Flender KMP Series

Brands by name

Popular brands

Siemens Flender KMP Series, Assembly And Operating Instructions Manual

Search results

Summary of Contents for Flender KMP Series

Reviews:

Related manuals for Flender KMP Series

Brands by name

Popular brands