Siemens FLENDER K DH Series Assembly And Operating Instructions Manual Download Page 34 | Manualshive

Page: 34 / 109

background image

BA 5846 en 05/2015

DANGER

Risk of explosion

Danger to life through ignition of any potentially explosive atmosphere through sparks.
If dimension "x

min.

" is fallen below, this means that the friction pads are worn too heavily and that sparking

may occur.
When this value "x

min.

" is reached, Siemens must be consulted.

NOTICE

Material damage

Risk of damage to or destruction of the backstop and/or the gear unit through incorrect direction of
rotation.
Do not allow the motor to run adversely to the blocking direction of the gear unit.
Observe the notice fixed to the gear unit.

DANGER

Risk of explosion

Danger to life through ignition of any potentially explosive atmosphere through overheating of the
backstop or through sparks.
If a potentially explosive atmosphere develops, the release mechanism (type FXRT only) must not be
operated.
If a unit of this type with release mechanism is used, the operating instructions for this backstop must be
followed.

5.8

Cooling

Depending on requirements, the gear unit is fitted with a fan, a cooling coil or a separately provided
oilsupply system. In case of use of a separately provided oilsupply system, the separate operating
instructions for this oilsupply system must also be observed.

Note

The oilsupply system must have been designed and manufactured for use in accordance with
Directive 94/9/EC.

Note

When fitting the gear unit free convection must be ensured on the housing surface, in order to definitely
avoid overheating the gear unit.

«
...
32
33
34
35
36
...
»

Summary of Contents for FLENDER K DH Series














































































































Reviews:

No comments

Related manuals for FLENDER K DH Series

Brand: Keithley Pages: 36

Brand: Rain-Flo Irrigation Pages: 16

Brand: Balanced Body Pages: 4

Brand: Fenton Pages: 16

Brand: Quark-Elec Pages: 2

Brand: Raymarine Pages: 3

SmartPilot ST8002

Brand: Raymarine Pages: 48

Brand: Raymarine Pages: 38

hsb2 PLUS Series

Brand: Raymarine Pages: 248

Brand: UNI-T Pages: 4

UPO3000E Series

Brand: UNI-T Pages: 94

Brand: UMS Pages: 92

Brand: Park House Healthcare Pages: 32

Brand: GE Pages: 289

Brand: MacDon Pages: 238

Brand: VaBroom Pages: 4

Brand: ATD Tools Pages: 7

SPLICE-500 MKII

Brand: Serpent Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands