Siemens FDA221 Technical Manual Download

Page: 48 / 114

Mounting / Installation
Preparatory work

48
Building Technologies

A6V10334410_h_en_--

Fire Safety

2015-09-29

5.1.3

Removing and installing the housing cover when the power

supply is switched off

NOTICE

Electrostatic discharge
Damage to electronic components in the aspirating smoke detector

●

When working on the open aspirating smoke detector, use anti-static floor

mats and anti-static work surfaces.

●

Ground yourself immediately before opening the housing, e.g. by touching a

ground point or wearing an anti-static belt.

When the housing cover is removed, you have access to:



The fixing screws



The cable entry



All the mechanical components



The electrical connections



The rear of the front indicator

Removing the housing cover

Summary of Contents for FDA221



















































































































Search results

Summary of Contents for FDA221

Reviews:

Related manuals for FDA221

Brands by name

Popular brands

Siemens FDA221, Technical Manual

Search results

Summary of Contents for FDA221

Reviews:

Related manuals for FDA221

Brands by name

Popular brands