manualshive.com logo in svg

Siemens E50417-H8940-C560-4, Manual, Page: 54 / 56

Share
Download
Siemens E50417-H8940-C560-4 Manual Download Page 54

Maintenance
7.1 Maintenance

SICAM P27, 3-phase Harmonic Power Meter, User Manual

E50417-H8940-C560-

4

, Release Date 

06.2018

54

7.1

Maintenance

• Voltage connection should be conducted strictly in accordance with voltage level marked on nameplate.

• Tighten the terminals and hang the meter securely to screen which is strong, refractory and vibration-free 

during installation. Upward view of the meter provides the best display effect, so it should be installed verti-
cally. 

• The meter should be stored in environment free of condensation at -35

℃

 to 70

℃

 and 

≤

 95% humidity in 

original package. At most 5 layers are allowable for stacking. The meter is inappropriate for storing after un-
packing. The meter should be stored in clean location free of hazardous substances or gas which may cause 
corrosion in air. 

• In the operating environment of the meter, lightning protection should be provided. 

■

Summary of Contents for E50417-H8940-C560-4

























































Reviews:

No comments