manualshive.com logo in svg

Siemens Desigo Touch Series, Installation And Commissioning Instructions, Page: 21 / 22

Share
Download
Siemens Desigo Touch Series Installation And Commissioning Instructions Download Page 21

21 / 22

Siemens

Desigo Touch and Web

CM111029en_04

Building Technologies

Compatibility & limitations – Firmware updates

2014-08-15

9.  When the upload process has reached a certain level, an error message is

displayed.

10.  Repeat now steps 1-8 above.

This time the upload will completely run the process:

11.  Wait until the device has

restarted

 following upload completion.

12.

Disconnect

 the USB connection.

Note

After device restart, the orange LED no longer is lit, and FWDT has returned to
normal mode.

2.7.3  Factory reset web interface PXG3.100

Given certain circumstances it may be desirable or necessary to factory reset the
device. If so, please exactly follow the procedure given below.

Attention:

The device will lose any password and other settings. Only the

IP network settings remain the same as before.

Procedure

1. Power

off

 device.

2. Power

on

 device.

3.  Wait for all LEDs to

light up and turn off

 again, then

4. Press

SVC

 button and hold until the green

RUN

 LED

flashes.

Then

5. Release

SVC

 button.

6.  Wait for the device to fully start up unconfigured. (

RUN

 LED is

on

,

SVC

 LED

flashes.

)

7.  Start firmware download process with SSA-DNT.

Summary of Contents for Desigo Touch Series























Reviews:

No comments