manualshive.com logo in svg

Siemens CP 443-5 Extended, Manual

Share
Download
Siemens CP 443-5 Extended Manual Download Page 24

5

Performance Data

B4 - 24

CP 443-5 Extended for PROFIBUS / Manual Part B4

Release 6/2005

C79000-G8976-C162-06

5.9

Other Characteristics

Note on DP:
The connected DP slaves can only be assigned to and serviced by one CPU.

 

Notice

If you use the CiR functionality, multicomputing is not possible.

Memory Reset on the CP

!

Warning

Please note that when you reset the CP memory using NCM Diagnostics or the
SIMATIC Manager, the configuration data on the CPU must also be deleted
otherwise the data will become inconsistent.

 

Special feature of the DP mode: 
If the CPU is in the RUN mode, the memory reset is rejected by the CP.

DP Diagnostic Frames when the CPU is in STOP 

All diagnostic frames from DPV0 standard slaves and all DP alarm frames from
DP - S7/DP - V1 standard slaves arriving when the CPU is in STOP mode are
handled as follows:

S

In “S7 - compatible” mode

The problems that still exist at the transition from CPU STOP to CPU RUN are
passed on the user program.

S

In DP - V1 mode

The diagnostic/alarm frames are forwarded even when the CPU is in STOP
mode, however, they must be evaluated by a suitable user program when the
module starts up.

Summary of Contents for CP 443-5 Extended




























Reviews:

No comments

Brands by name

Popular brands

Load more brands