manualshive.com logo in svg

Siemens A53689, Installation & Operation Manual

Share
Download
Siemens A53689 Installation & Operation Manual Download Page 32

INSTALLATION 
_________________________________________________________________________________________________________ 

3-4 

COM-00-21-04                                                                                                                                                          OCTOBER 2021 
Version No.: A.1 

3.3 

Mechanical Installation 

3.3.1  Mounting Procedure 

 
Mounting brackets are provided for attaching the Airlink Venus enclosure to a vertical flat 
surface. Note that Airlink Venus has a passive cooling system and as such, the external cooling 
fins should not be blocked. Provide adequate airflow around the radio enclosure, maintaining a 
minimum 2” clearance from the front, sides, top, and rear surfaces. 

 

The Airlink Venus radio can be mounted with either the connectors facing right, left, or down. 
(Up is possible, but not recommended to avoid ingress of dust and other foreign matter). Fasten 
the radio using four #12 (M5) screws with washer and lock-washer to a flat and level surface 
using the mounting brackets provided. See Figure 3-1. 

 

RF antenna and GPS antenna are not included with the Airlink Venus radio. Antennas should be 
installed by qualified personnel and care should be taken with its grounding and connection to 
coaxial cable. 
 
 

 

 

Figure 3-2   Mounting Dimensions – Ventilation Allowances  

 

Summary of Contents for A53689







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands