Siemens 7XV5655-0BA00 Application Instructions Download Page 9 | Manualshive

Page: 9 / 53

background image

English

7XV5655-0BA00

9 / 53

C53000-G1176-C174-3

Application in Substations

Using a 7XV5655-0BA00 Serial Hub with a fixed IP address, one or more SIPROTEC
protection units can exchange serial data via an Ethernet network.
On the operating PC, a configuration tool is used to link virtual COM port with the IP
address of a Serial Hub. Using DIGSI 4 it is then possible to operate all protection units
connected to the Serial Hub via the virtual COM port.

The protection unit is connected to the Serial Hub via its serial interface. The serial interface
types available are RS232 or RS485 (same connector), and FO (fibre optical). The serial
data are converted to the UDP protocol with error detection and correction as useful data in
the Serial Hub and transmitted via the TCP/IP Ethernet network.
The hub meets the requirement for standard compliant, uninterrupted transmission of serial
DIGSI

®

or IEC 60870-5-103/101 frames via the network by listening into the serial frame

traffic and sending the serial IEC telegrams via the Ethernet packed in blocks. Both full-
duplex and half-duplex data transmission (RS485) are possible. The serial control lines are
not supported. The Serial Hub can be configured with password protection.
Configuration of the Serial Hub is performed using the configuration tool included in the
scope of supply.

RS485-Bus-Cable 7XV5103

SIPROTEC

SIEMENS

L1  402,1A         Max450.1A
L2  402,1A         Max450.1A
L3  402,1A         Max450.1A
E      00.0A

Anr. L1
Anr. L2
Anr. L3
Anr. Erde
Automat

RUN

ERROR

LAN

FO-Cable 6XV8100

SIPROTEC

SIEMENS

L1  402,1A         Max450.1A
L2  402,1A         Max450.1A
L3  402,1A         Max450.1A
E      00.0A

Anr. L1
Anr. L2
Anr. L3
Anr. Erde
Automat

RUN

ERROR

Router / Switch

DIGSI 4

Config-Tool

Patch-Cable

WAN (Private Network)

2

1

3

4

Ethernet-

Hub

7XV5655

5

6

up

Ethernet-

Hub

7XV5655

Mini-Star-

coupler

7XV5450

INPUT

L2 402,1A Max450.1A
L3 402,1A Max450.1A

L2 402,1A Max450.1A
L3 402,1A Max450.1A

7XV5

1

01

SIPROTEC

SIEMENS

L1  402,1A         Max450.1A
L2  402,1A         Max450.1A
L3  402,1A         Max450.1A
E      00.0A

Anr. L1
Anr. L2
Anr. L3
Anr. Erde
Automat

RUN

ERROR

SIEMENS

RUN

ERROR

Anr. L1

Anr. L2

RS485-FO
Converter

7XV5650

SIEMENS

RUN

ERROR

Anr. L1

Anr. L2

7XV5103

Max. 31 SIPROTEC 3

Devices with

RS485-Interface

Max. 4 SIPROTEC 3 Devices

with optical Interface

Station-PC for
Remote control
and Configuration for
the Ethernet-Modems

Substation-

modem 1

Substation-

modem 2

SIPROTEC 4

with Ethernet-

Interface

Max. 31 SIPROTEC 4 Devices

with RS485-Interface

Fig. 2: Serial Hub, application in substations

«
...
7
8
9
10
11
...
»

Summary of Contents for 7XV5655-0BA00






















































Reviews:

No comments

Related manuals for 7XV5655-0BA00

RackSwitch G8332

Brand: IBM Pages: 18

Brand: Fairchild Pages: 14

Brand: Touch-plate Pages: 12

Brand: Watt Stopper Pages: 10

Brand: Comtrend Corporation Pages: 2

Brand: Lindy Pages: 38

Brand: NTI Pages: 69

Brand: Datavideo Pages: 64

Brand: Cable Electronics Pages: 16

Brand: 3Com Pages: 74

Brand: Versitron Pages: 46

BOCAHUB-16 Plus BEN220

Brand: Boca Pages: 56

Brand: DVIGear Pages: 11

Brand: Pakedge Device & Software Pages: 8

Brand: Edge-Core Pages: 2

Brand: VNS Pages: 8

Brand: Manhattan Pages: 2

Brand: Icy Box Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands