Siemens 3VA1 100 A Manual Download

Page: 253 / 532

Accessories

4.5 Manual operators

3VA molded case circuit breakers
Manual, 04/2015, A5E03603177010-02

253

4.5.5.2

Locking and interlocking by the rotary operator

The following manual operators can be locked and interlocked by the rotary operator:

●

Front mounted rotary operator

●

Rotary operator with shaft stub

●

Door mounted rotary operator

●

Side wall mounted rotary operator

The manual operators can be locked by up to three padlocks with a shackle diameter of

between 5 and 8 mm or by means of cylinder locks (type Ronis). Manual operators can be

interlocked only by means of cylinder locks (type Ronis).
In addition, door mounted rotary operators and side wall mounted rotary operators can also

be locked or interlocked by additional cylinder locks (type Kaba) at the masking frame in the

cubicle door or side panel.
Padlocks and cylinder locks are not included in the scope of supply of manual rotary

operators.

Locking with padlocks

All rotary operators are equipped with a padlock locking unit. This locking unit is simply

pulled out of the rotary operator.
Example of rotary operator with shaft stub:

Lockable switching positions:

●

Position OFF (O)

Summary of Contents for 3VA1 100 A





















































































































































































































































































































































































































































































































































Search results

Summary of Contents for 3VA1 100 A

Reviews:

Related manuals for 3VA1 100 A

Brands by name

Popular brands

Siemens 3VA1 100 A, Manual

Search results

Summary of Contents for 3VA1 100 A

Reviews:

Related manuals for 3VA1 100 A

Brands by name

Popular brands