Siemens Nixdorf D1025 Technical Manual Download Page 20

Page: 20 / 20

A26361-D1025-Z120-7-7419

A26361-D1025-Z120-7-7419

System board D1025

Technical Manual

October 1998 edition

Creative is a registered trademark, Sound Blaster 16 and VIBRA 16C are trademarks of Technology
Ltd.

Intel and Pentium are registered trademarks and MMX and OverDrive are trademarks of Intel
Corporation, USA.

AMD-K6 is a trademark of Advanced Micro Devices, Inc.

Microsoft, MS, MS-DOS and Windows are registered trademarks of Microsoft Corporation.

PS/2 and OS/2 Warp are registered trademarks of International Business Machines, Inc.

All other trademarks referenced are trademarks or registered trademarks of their respective owners,
whose protected rights are acknowledged.



Siemens Nixdorf Informationssysteme AG 1998.

All rights, including rights of translation, reproduction by printing, copying or similar methods, even of
parts are reserved.

Offenders will be liable for damages.

All rights, including rights created by patent grant or registration of a utility model or design, are
reserved.

Delivery subject to availability. Right of technical modification reserved.

Summary of Contents for D1025





















Search results

Summary of Contents for D1025

Reviews:

Related manuals for D1025

Brands by name

Popular brands

Siemens Nixdorf D1025, Technical Manual

Search results

Summary of Contents for D1025

Reviews:

Related manuals for D1025

Brands by name

Popular brands