background image

SIDESHIFT INSTALLATION GUIDE 

V1.9

 

 

      

13 

BATTERY STORAGE 

Over time, batteries self-discharge, even when disconnected.  Some new batteries 

may have a self-discharge of 1-2% per month, but depending on the type and age 
of the battery, it can rise to 6% per month or more. 

If the battery is coated with moist dirt and corrosion by-products, discharge rates 

can be even higher.  Make sure the battery is clean and free of dirt and corrosion on 
and around the terminals. 

If the battery is a flooded type, top up the electrolyte, ensuring that it is above the 

plates and below the vent cap well. 

Fully charge the battery before storage, and store in a cool, dry place.  Cooler 
batteries will self-discharge at a lower rate than warm batteries. 

Check the terminal voltage of the battery periodically using the digital 
voltmeter located on the fuse holder.

  When the terminal voltage drops below 

12.4 volts (75% capacity), charge it until fully charged.  More frequent charging is 

preferred if convenient.  It is recommended to charge the battery every three 
months. 

Note that as charge capacity decreases, the freezing point of the electrolyte 

increases.  This is important because the electrolyte must not be allowed to freeze. 
At 62% capacity, the freezing point is -26.5°C/-16°F;  at 85% capacity, it is -52°C/-
62°F. 

CONNECTING BATTERIES IN PARALLEL TO BOOST CCA 

You can double the CCA supplied from a single battery by connecting a second 
battery in parallel to the first.  You may prefer this alternative to buying a larger 
single battery with the required CCA rating. 

 

Figure 1: Two batteries in parallel, doubling CCA 

Summary of Contents for HB340































Reviews: