SICK GR18 Series Operating Instruction Download Page 12

Page: 12 / 56

Abb. 12: G

Fehlerdiagnose

Tabelle 17 zeigt, welche Maßnahmen durchzuführen sind, wenn die Funktion des Sensors nicht
mehr gegeben ist.

Tab_Fehlerdiagnose

Anzeige-LED / Fehlerbild /

LED indicator/fault pattern

Ursache /

Cause

Maßnahme /

Measures

grüne LED leuchtet nicht /

Green LED does not light up

keine Spannung oder Spannung
unterhalb der Grenzwerte /

No voltage or voltage below the
limit values

Spannungsversorgung prüfen,
den gesamten elektrischen
Anschluss prüfen (Leitungen und
Steckerverbindungen) /

Check the power supply, check all
electrical connections (cables and
plug connections)

grüne LED leuchtet nicht /

Green LED does not light up

Spannungsunterbrechungen /

Voltage interruptions

Sicherstellen einer stabilen Span‐
nungsversorgung ohne Unterbre‐
chungen /

Ensure there is a stable power
supply without interruptions

grüne LED leuchtet nicht /

Green LED does not light up

Sensor ist defekt /

Sensor is faulty

Wenn Spannungsversorgung in
Ordnung ist, dann Sensor austau‐
schen /

If the power supply is OK, replace
the sensor

| SICK

Irrtuemer

8016955.16B5

Summary of Contents for GR18 Series

























































Search results

Summary of Contents for GR18 Series

Reviews:

Related manuals for GR18 Series

Brands by name

Popular brands

SICK GR18 Series, Operating Instruction

Search results

Summary of Contents for GR18 Series

Reviews:

Related manuals for GR18 Series

Brands by name

Popular brands