SICK GR18 Series Operating Instruction Download Page 6

Page: 6 / 56

Image 5: C

Image 6: G

Fault diagnosis

Table 7 indicates which measures are to be taken if the sensor stops working.

Tab_Fault diagnosis

LED indicator/fault pattern /

LED indicator/fault pattern

Cause /

Cause

Measures /

Measures

Green LED does not light up /

Green LED does not light up

No voltage or voltage below the
limit values /

No voltage or voltage below the
limit values

Check the power supply, check all
electrical connections (cables and
plug connections) /

Check the power supply, check all
electrical connections (cables and
plug connections)

Green LED does not light up /

Green LED does not light up

Voltage interruptions /

Voltage interruptions

Ensure there is a stable power
supply without interruptions /

Ensure there is a stable power
supply without interruptions

Green LED does not light up /

Green LED does not light up

Sensor is faulty /

Sensor is faulty

If the power supply is OK, replace
the sensor /

If the power supply is OK, replace
the sensor

| SICK

Irrtuemer

8016955.16B5

Summary of Contents for GR18 Series

























































Search results

Summary of Contents for GR18 Series

Reviews:

Related manuals for GR18 Series

Brands by name

Popular brands

SICK GR18 Series, Operating Instruction

Search results

Summary of Contents for GR18 Series

Reviews:

Related manuals for GR18 Series

Brands by name

Popular brands