background image

Chapter 

9

Operating Instructions 

Flexi Classic Gateways

 

120

 

© SICK AG • Industrial Safety Systems • Germany • All rights reserved 

8011834/YT28/2016-03-15 

Subject to change without notice 

EtherNet/IP Gateway 

9.10.2

 

Data set 6, can be compiled by the user 

The contents of Data set 6 can be compiled by the user.  
If the option 

Return only enabled Data

 is activated in the configuration of the data set 

(see section “Configuration …” above), the data set can have a different length depending 
on the compilation. The maximum length is 124 bytes. The minimum length is 2 bytes. 
The selected data are transferred for all Flexi Classic modules respectively. 
The data are zeroed for modules that do not exist. 
If data is expected in 16-bit words and in the format Big Endian (e.g. Modbus/TCP), it is 
transferred with the more significant byte first. 

 

Data set 6 

Byte  
1-124

CRC-H 

CRC-L 

    

MKD1.1 MKD2.1 MKD1.2 MKD2.2 MKD1.3 MKD2.3 

MKD1.4 MKD2.4 MKD1.5 MKD2.5 MKD1.6 MKD2.6 

MKD1.7 MKD2.7 MKD1.8 MKD2.8 MKD1.9 MKD2.9 

MKD1.10 MKD2.10 MKD1.11 MKD2.11 MKD1.12 MKD2.12 

MKD1.13 MKD2.13  

 

 

 

MOD-ID1 MOD-ID2 MOD-ID3 MOD-ID4 MOD-ID5 MOD-ID6 

MOD-ID7  MOD-ID8  MOD-ID9  MOD-ID10 MOD-ID11 MOD-D12 

MOD-13 

    0 

SW Version 
Byte 1, 
Module 1 

SW Version 
Byte 2, 
Module 1 

SW Version 
Byte 1, 
Module 2 

SW Version 
Byte 2, 
Module 2 

SW Version 
Byte 1, 
Module 3 

SW Version 
Byte 2, 
Module 3 

SW Version 
Byte 1, 
Module 4 

SW Version 
Byte 2, 
Module 4 

SW Version 
Byte 1, 
Module 5 

SW Version 
Byte 2, 
Module 5 

SW Version 
Byte 1, 
Module 6 

SW Version 
Byte 2, 
Module 6 

SW Version 
Byte 1, 
Module 7 

SW Version 
Byte 2, 
Module 7 

SW Version 
Byte 1, 
Module 8 

SW Version 
Byte 2, 
Module 8 

SW Version 
Byte 1, 
Module 9 

SW Version 
Byte 2, 
Module 9 

SW Version 
Byte 1, 
Module 10 

SW Version 
Byte 2, 
Module 10 

SW Version 
Byte 1, 
Module 11 

SW Version 
Byte 2, 
Module 11 

SW Version 
Byte 1, 
Module 12 

SW Version 
Byte 2, 
Module 12 

SW Version 
Byte 1, 
Module 13 

SW Version 
Byte 2, 
Module 13 

 

Function 1 

Function 2 

Function 3 

Function 4 

Function 5 

Function 6 

Function 7 

Function 8 

Function 9 

Function 10

Function 11

Function 12

Function 13

0

Note 

Tab. 112: Data set 6 of the 
UE410-EN 

Summary of Contents for Flexi Classic





























































































































































Reviews: