Sices GC315 User And Installation Manual Download Page 3

GCxxxLink

–User and installation guide  

2

 

 

The device necessarily requires a SIM for its operation. 
If  you  wish  to  use  the  packet  data  functions  (communicate  with  the  device 
through  TCP/IP,  use  of  “

Si.Mo.Ne

”  system  etc.)  a  SIM  with  an  internet 

connection  active  plan  is  required.  The  SIM  card  in  the  device  determines 
whether the device supports 

GSM/GPRS/EDGE

LTE Cat M1

 and 

NB-IoT

 or 

all these connections. 
 
Make sure that your SIM supports the packet data network type you want to 
use. - i.e. if you want to use the module in 

LTE Cat M1

 network you have to confirm with the operator that the 

particular SIM card supports 

LTE Cat M1

 network. 

      
SIM Type: standard SIM Card type 

Mini-SIM

 (or 

PLUG-IN

).  

 

 

INFORMATION

: Make sure SIM card does not require PIN 

code.  If  it  does,  it  is  possible  to  disable  it  in  any  common 
network unlocked mobile telephone
. 

Ensure the device is powered off, then remove the back cover from 
the device. 
Remove the access cover that encloses the SIM holder, the 
antenna connectors and the battery switch. Insert a small 
screwdriver in the little retention hooks and make a slight leverage 
to remove the panel. 

 

 

After opening the cover, you will see the following parts his picture 
shows the inner part; 

 

A. 

SMA FEMALE connector for GSM - LTE antenna. 

B. 

SMA FEMALE connector for GNSS antenna. 

C. 

SIMcard holder slide. 

D. 

Switch for internal optional battery (inserted/not inserted). 

E. 

Yellow LED: indicator for Network Status (NET). 

F. 

Green  LED:  indicator  for  Module  power  on/off  status 
(STATUS). 

G. 

Internal Battery connector 

 
 
 
 

 

1)  Pull back the upper cover, it clicks as it unlocks. (fig.1).  

2)  Open the SIM card holder, it hinges towards you 

(fig.2). 

3) 

Slide in the SIM card, ensuring the “edge cutout” is as 
shown (fig.3). 

4)  Close the cover, press it down and slide it as shown 

until it clicks into place (fig.4). 

5)  Insert the antenna connectors into the holes of the 

access cover and gently screw them to the relevant receptacles (fig.5). 

6) 

Move the switch to the right in “BATTERY ON” position  (see fig. 6 and notes below).  

15 
mm 

25 mm 

Summary of Contents for GC315









Reviews: