Shuttle Spacewalker ME17 Manual Download Page 4

Page: 4 / 83

- 2 -

STEP 11 Connect External Peripherals to Back Panel ....................... 21

STEP 12 First Time System Boot Up ................................................... 23

STEP 13 Install Drivers & Software Components ................................. 24

3.2 JUMPER SETTINGS .......................................................................... 25

JUMPERS & CONNECTORS GUIDE .................................................. 26

Set Keyboard & PS/2 Mouse Power-On (J1) ....................................... 29

CPU Host Frequency Setting (J8) ....................................................... 30

Core CPU Voltage Setting (J24) .......................................................... 31

ICH Voltage Setting (J25) .................................................................... 31

AMR Slot Setting (J9 ) .......................................................................... 32

Over-Clocking the CPU (J10A & J26 For Reference Only) .................. 32

Clear the CMOS (J12) .......................................................................... 34

Clear Password (J15) ........................................................................... 34

Factory Reserved (J18) ........................................................................ 35

Suspend to RAM (J23) ......................................................................... 35

Boot-Block Protection (J16) .................................................................. 36

PS/2 Keyboard & PS/2 Mouse Connectors .......................................... 36

USB1/USB2 Port Connectors ............................................................... 36

COM1 Connector ................................................................................. 37

VGA Connector .................................................................................... 37

Parallel Port Connector ........................................................................ 37

Line-Out ............................................................................................... 37

Line-In .................................................................................................. 37

Mic-In ................................................................................................... 37

MIDI/GAME Port .................................................................................. 38

ATX Power On/Off Switch Connector (PWON) .................................... 38

Green LED Connector (GLED) ............................................................. 38

EPMI Connector (EPMI) ....................................................................... 39

Summary of Contents for Spacewalker ME17




















































































Search results

Summary of Contents for Spacewalker ME17

Reviews:

Related manuals for Spacewalker ME17

Brands by name

Popular brands

Shuttle Spacewalker ME17, Manual

Search results

Summary of Contents for Spacewalker ME17

Reviews:

Related manuals for Spacewalker ME17

Brands by name

Popular brands