Shuttle MV43P User Manual Download Page 65

Page: 65 / 73

- 61 -

Plug and Play Aware O/S

Enable this item if you are using an O/S that supports Plug and Play such
as Windows 95 or 98.

The choice: Yes or No.

Share Memory Size

This item lets you allocate a portion of the main memory for the onboard
VGA display application with three options of 8/16/32MB.

The choice: 8MB,16MB,32MB or None.

Primary Graphics Adapter

This item indicates if the primary graphics adapter uses the PCI or the
AGP bus. The default AGP setting still lets the onboard display work and
allows the use of a second display card installed in an AGP slot.

The choice: Onboard or PCI.

Allocate IRQ for PCI VGA

If this item is enabled, an IRQ will be assigned to the PCI VGA graphics
system. You set this value to No to free up an IRQ.

The choice: Yes or No.

PCI IDE BusMaster

This item enables or disables the DMA under DOS mode. We recommend
you to leave this item at the default value.

The choice: Enable or Disable.

PCI /Plug and Play Setup

Summary of Contents for MV43P










































































Search results

Summary of Contents for MV43P

Reviews:

Related manuals for MV43P

Brands by name

Popular brands

Shuttle MV43P, User Manual

Search results

Summary of Contents for MV43P

Reviews:

Related manuals for MV43P

Brands by name

Popular brands