background image

PSM1000

P10T

Dual Wireless 

Transmi

tter

with Audio

 Reference 

Companding

CLIP

CLIP

PSM1000

P10T

Dual Wireless Transmitter
with Audio Reference 
Companding

CLIP

PSM1000

P10T

Dual Wireless Transmitter
with Audio Reference 
Companding

CLIP

PSM1000

P10T

Dual Wireless Transmitter
with Audio Reference 
Companding

Quickstart Instructions

Rack Mount Transmitter

1.  Connect to a power outlet using the supplied power cable.
2.  Attach the supplied antennas to the 

antenna out

 BNC 

connectors.

3.  Connect the audio source, such as the output of a mixer, to the 

audio inputs. You can use both input jacks or choose either one 

for a mono source.

4.  Switch RF off and power on.
5.  For mono (one input), access the 

Audio

 menu and select 

Mono

Set the input sensitivity to match the source using the 

Util

 > 

Audio

 > 

 INPUT

 setting.

6.   Adjust the audio source level so that, for the average input signal 

level, the top two yellow LEDs flicker and the lower LEDs are 

solid. If the red clip LED illuminates and a warning appears on the 

LCD, the inputs are overdriven. Decrease the audio input level to 

+4 dBu

 from the 

Audio

 menu. If the signal level is too low, change 

the input sensitivity to 

–10 dBV

Bodypack

Open by pressing the latches on both sides and pulling. Insert the 

batteries or battery pack and attach antennas. Turn on using the vol-

ume knob. The battery light illuminates.

Scan and Sync

1.  On the bodypack, press the 

scan

 button. The display flashes 

SYNC NOW...

.

2.  Align the IR windows on the bodypack and rack unit, the IR win-

dow on the transmitter illuminates. Press the 

sync

 button on the 

transmitter. The rack unit 

Level

 LEDs flash, and the screen dis-

plays 

SYNC SUCCESS

.

3.  Turn the RF switch on. The blue RF LED illuminates on the 

bodypack to indicate that it is detecting the transmitter. The 

bodypack also displays the RF signal strength (RF).

4. 

Important: 

Turn bodypack volume down before plugging in 

earphones.

5.  Insert the earphones and slowly turn up the volume.

Important: 

Remove the protective film from the face of the transmit-

ter or the IR sync may not work.

3

Summary of Contents for P10R-G10



















Reviews: