background image

Shure Incorporated

20/22

8.

9.

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20.

21.

DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other apparatus (in­

cluding amplifiers) that produce heat. Do not place any open flame sources on the product.

DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one 

wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third 

prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replace­

ment of the obsolete outlet.

PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the 

point where they exit from the apparatus.

ONLY USE attachments/accessories specified by the manufacturer.

USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a 

cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

UNPLUG this apparatus during lightning storms or when unused for long periods of time.

REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any 

way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, 

the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vases, on the 

apparatus.

The MAINS plug or an appliance coupler shall remain readily operable.

The airborne noise of the Apparatus does not exceed 70dB (A).

Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connec­

tion.

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.

Operate this product within its specified operating temperature range.

WARNING: 

Voltages in this equipment are hazardous to life. No user-serviceable parts inside. Refer all servicing to qualified 

service personnel. The safety certifications do not apply when the operating voltage is changed from the factory setting.

Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate this equipment.

WARNING FOR ALL EARPHONES!

For safe and correct use of earphones, read this manual before use. Keep the manual and safety information in a convenient 

place for future reference.

WARNING

LISTENING TO AUDIO AT EXCESSIVE VOLUMES CAN CAUSE PERMANENT HEARING DAMAGE. USE AS LOW A VOL­

UME AS POSSIBLE. 

Over exposure to excessive sound levels can damage your ears resulting in permanent noise-induced 

hearing loss (NIHL). Please use the following guidelines established by the Occupational Safety Health Administration (OSHA) 

on maximum time exposure to sound pressure levels before hearing damage occurs.

90 dB SPL

at 8 hours

95 dB SPL

at 4 hours

100 dB SPL

at 2 hours

105 dB SPL

at 1 hour

110 dB SPL

115 dB SPL

120 dB SPL

Summary of Contents for AXT600























Reviews: