background image

 

WARNING 

 
 
 
 
 
 

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY  

BEFORE YOUR INITIAL START-UP! 

 

SAFETY INSTRUCTIONS 

Every person involved with the installation, operation and maintenance of this device have to: 

-

 

be qualified 

-

 

follow the instructions of this manual 

 
 
 
 
 
 

Before your initial start-up, please make sure that there is no damage caused by transportation. Should there 
be any, consult your dealer and do not use the device. 
 
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to follow 
the safety instructions and warning notes written in this manual. 
 
Please consider that damages caused by manual modifications to the device are not subject to warranty. 
 
This device contains no user-serviceable parts. Refer servicing to qualified technicians only. 

 

IMPORTANT:

 

The manufacturer will not accept liability for any resulting damages caused by the non-
observance of this manual or any unauthorized modification to the device. 

 

 

Never let the power-cord come into contact with other cables! Handle the power-cord and all 
connections with the mains with particular caution! 

 

Never remove warning or informative labels from the unit. 

 

Never use anything to cover the ground contact. 

 

Do not insert objects into air vents. 

 

Do not connect this device to a dimmerpack. 

 

Never look directly into the light source 

 

Do not switch the device on and off in short intervals, as this would reduce the lamp’s life. 

 

Do not touch the device’s housing bare-handed during its operation (housing becomes very hot).  

 

Only use device indoor, avoid contact with water or other liquids. 

 

Avoid flames and do not put close to flammable liquids or gases. 

 

Always keep case closed while operating. 

 

Always allow free air space of at least 50 cm around the unit for ventilation. 

 

Always disconnect power from the mains, when device is not used, before cleaning or when 
replacing lamp! Only handle the power-cord by the plug. Never pull out the plug by tugging the 
power-cord. 

 

Make sure that the available voltage is not higher than stated on the rear panel. 

 

Make sure that the power-cord is never crimped or damaged. Check the device and the power-
cord from time to time. 

CAUTION! 

Keep this device away from rain and moisture! 

Unplug mains lead before opening the housing! 

CAUTION! Be careful with your operations. 

With a dangerous voltage you can suffer 

a dangerous electric shock when touching the wires!

 

 

Summary of Contents for LED Orbit I



















Reviews: