®
®
Shoreport
SHOREMASTER.COM
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
Keel Roller Rear Assembly
1001786
1
1
Washer Flat 3/8 SS
1002599
4
2
3/8 x 3/4 Button Head Socket Cap Screw
1001788
4
3
Keel Roller Assembly with Hardware
1006595
1
-
Front Keel Roller Assembly
1001776
1
4
Shoreport 58" x 138"
-
1
5
Washer Flat 3/8 x 1.25 x .125 Rubber
1000613
4
6
Keel Roller Spacer Kit
1003475
1
-
3/8 x 1-1/2 Button Head Cap Screw
1000655
4
7
Keel Roller Spacer Plate
1013375
2
8
Optional Float (adds 50lbs cap each)
1004236
6
9
3/8 x 2-1/4 Flat Head Machine Screw
1000505
2
10
8" Plastic Cleat
1001089
1
11
1
5
3
2
ShorePort Parts List
Instructions
6
4
9
10
Note:
The front of the ShorePort is 16" tall and will have a freeboard of about 14" without a PWC on it. The
rear roller should rest about half way out of the water without a PWC on it.
The freeboard can be increased
by adding supplemental floatation (item 10).
11
Not complying with the
procedures and precautions outlined in
this manual may result in personal injury
or death and will invalidate the warranty.
Step 1.
You may need to adjust rollers for best results. See next page
for adjustment options.
Step 2.
See Shoreport anchoring and attachment options page for
available methods to anchor the Shoreport. (Pile guides, flexi-hinges,
connectors, etc.)
Note:
Add optional floats if necessary. (adds 50lbs each)
4
8
2
3
DETAIL Position - A
DETAIL Position - B
DETAIL Position - C
DETAIL Position - D
DETAIL Position - E
DETAIL Position - F
DETAIL Position - G
Position - A
Position - B
Position - C
Position - D
Position - E
Position - F
Position - G
ShorePort Keel Roller Adjustment
Instructions
The rollers on the Shoreport have multiple adjustment locations in order to adjust the Shoreport to your personal
water craft.
The front and middle rollers can be placed in three different slots and can also be flipped with axle above or below the
plates. The rear roller can also be flipped but has only one location.
To adjust, use a 7/32" hex key to remove the four 3/8 button head bolts holding the roller in, move to desired position,
and put the bolts back in to secure in place.
For PWC's that are difficult to unload we recommend having the front roller in the most forward position with the axle
flipped above the plates (Position B) so it is the highest it can be and the middle roller in the most forward position
with the axle facing down into the slots of the Shoreport (Position C).
With the many different designs of PWC's available you will need to adjust the rollers to fit your specific watercraft. As
a general guideline, raising the front and middle rollers makes it easier to unload the PWC. However if the rollers are
too high the PWC may not stay on the Shoreport and the rollers may need to be lowered. If the rollers do not provide
enough height in the forward position with the axle up, there is a spacer kit available to raise the roller another 1/2
inch, part number 1003475 as shown in Position A.
-The keel rollers on the ShorePort may be adjusted to make it
easier to get your PWC on and off of the ShorePort.
-The middle and front rollers can be adjusted in the different
positions as shown. The axle of the roller assembly can be
positioned facing up or down and can be placed in any three of
the roller positions.
-To move the rollers use a 7/32" hex key wrench and remove
the four 3/8" button head bolts holding the roller to the
ShorePort. Move the roller to the desired position and
re-attach using the same 3/8" button head bolts. For further
adjustment a Keel Roller Spacer kit (P/N: 1003475) is
available and can be used in positions D,E, and F as shown in
position G.
-The rear keel roller may also be adjusted by flipping it over so
the axle for the roller is on top of the mounting plates. Roller
positioning will vary depending on the type of PWC you have.
You will have to try different roller positions to find what works
best for your PWC.
A
B
C
D
E
A - Highest Position with Spacer Kit
B - Highest Position no Spacer Kit Axle Up
C - Roller in Forward (High) Position
D - Roller in Middle Position
E - Roller in Rear (Low) Position
The front and middle rollers can be used in
all of the above positions. Positions D and E
can also be used with the axle up. The axle
needs to be up in order to use the spacer kit.
The spacer kit can be used in any of the
three slots.
To the left, recommended roller position for
PWC's that are difficult to remove from the
Shoreport. Front roller in position B, middle
roller in position C.
