SHOREMASTER.COM
SWIm RAftS
SWIm RAftS
A
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
QC Connector Bracket
1004187
-
1
T Handle
1000876
1
2
Carriage Bolt 3/8 x 1.75
1001959
2
3
Flange Nut 3/8
1001802
2
4
NUT 3/8
1001803
1
5
4
2
5
3
1
Failure to follow instructions may
result in personal injury and may
invalidate the applicable warranty.
Step 1.
Attach the QC Connector Bracket
to the TS9 Frame with two 3/8 x 1 3/4
Carriage Bolts and two 3/8 Flange Nuts - as
shown.
Note:
The QC Bracket must be bolted to the
TS9 Frame
Note:
The TS9 Frame must be supported
by legs.
Step 2.
Set the 9" Truss Dock onto the QC
Brackets and secure using the T-Handles.
QC Connector TS9 to Truss Dock
Instructions
Part #: 1004187
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
3 STEP LADDER FRAME LEFT
1005615
1
1
3 STEP LADDER FRAME RIGHT
1005616
1
2
Prt Ladder Step 15.0
1005785
3
3
Bolt Carriage 1/4-20 x .75 SS 304
1001950
12
4
1/4" NUT BRASS
1001797
12
5
POLY WASHER 3/8 ID X 1"OD X .093
1002469
2
6
Pin Snap 3/8 x 1.75
1000338
2
7
Washer Flat 3/8 SS
1002599
4
8
Nut Nyloc 3/8-16 Brass
1001805
2
9
Ladder Pivot Left
1001778
1
10
Ladder Pivot Right
1001779
1
11
BOLT 3/8" x 2.0 PHILLIPS MACH SCREW
1002426
2
12
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
Swim Raft Rubber Anchor Hold
1001094
2
1
3 Step Pivoting Ladder
1007634
1
2
Ladder Brace
1004979
1
3
3/8 X 6-1/2 Hex Bolt
1002447
2
4
3/8" Washer
1002599
6
5
3/8 Nyloc Nut
1001805
2
6
3/8 X 1 Hex Bolt
1002419
2
7
3/8 Lock Washer
1002596
2
8
D
See 1006596 - Pivoting Ladder instructions
for assembly and operating steps.
12
6
8
6
8
9
4
3
2
1
10
5
7
11
Poly Swim Raft w/3 Step Ladder
Instructions
Part #: 1007970 - Yellow
1007980 - Grey
1024603 - Tan
5
8
7
2
3
5
6
1
4
5
Attach Ladder
Step 1.
The rear of each Ladder Pivot is bolted through the
hole marked on the drawing as Hole Location. Two 3/8" x
6-1/2" bolts and two 3/8" washers are placed through the
rear of each ladder pivot. The bottoms of the two bolts are
secured through a Ladder Brace using two 3/8" washers and
two 3/8" Nyloc nuts.
Step 2.
The front of each Ladder pivot is bolted into a
threaded insert molded into the raft using two 3/8" x 1" bolts,
two 3/8" washers and two 3/8" lock washers on top.
Hole
Location
Failure to follow instructions may result in personal injury and may invalidate the
applicable warranty.
