DOUBLE INSULATION
Do not operate if cord, plug or appliance is damaged. In your double insulated appliance, two systems of insulation are provided instead of
grounding. No grounding means is provided nor should a means for grounding be added to the appliance.
NOTE:
If power cord needs to be replaced, use only a Shop-Vac Service Agent.
EXTENSION CORDS
NOTE:
STATIC SHOCKS ARE COMMON IN DRY AREAS OR WHEN THE RELATIVE HUMIDITY OF THE AIR IS LOW. THIS IS ONLY TEMPORARY AND
DOES NOT AFFECT THE USE OF THE APPLIANCE. TO REDUCE THE FREQUENCY OF STATIC SHOCKS IN YOUR HOME, THE BEST REMEDY
IS TO ADD MOISTURE TO THE AIR WITH A CONSOLE OR INSTALLED HUMIDIFIER.
Use only a cord extension set that complies with AS3199. Conductor size must be 1.0mm
2
for length up to 25 metres and 1.5mm
2
for length
from 25 - 32 metres.
UNPACKING AND SET-UP
1. Remove tank cover and any accessories which may have been
shipped in the tank.
2. Before replacing tank cover, please refer to DRY PICK UP or WET
PICK UP OPERATION in this manual to ensure you have the proper
filters installed for your cleaning operation.
3. Replace tank cover.
4. Slip cleaner end of flexible hose into the intake port.
5. Attach the extension wands to the accessory end of the hose. Twist
slightly to tighten the connection.
6. Attach one of the cleaning accessories (depending on your cleaning
requirements) to the extension wand. Twist slightly to tighten the
connection.
7. Plug the cord into the wall outlet. Your cleaner is ready for use.
I = ON O = OFF
CASTER ASSEMBLY
LIMITED THREE-YEAR WARRANTY
Shop-Vac warrants the vacuum cleaner for three years from the date of purchase to correct by repair or parts replacement without charge, any
product defect due to faulty material or workmanship provided that the vacuum cleaner is not used for rental service. This warranty does not
cover accessories. Simply return the complete unit, with a copy of the receipt, to the place where you purchased your vacuum cleaner. Shop-Vac
assumes no responsibility for damage or faulty performance caused by misuse or careless handling, or where repairs have been made or
attempted by others. Proof of purchase date is required. This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have
the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
WARNING -
DO NOT LEAVE VACUUM UNATTENDED WHEN IT IS PLUGGED IN AND/OR OPERATING.
UNPLUG UNIT WHEN NOT IN USE.
SAVE THESE INSTRUCTIONS!
You will find four caster feet
(Figure 1)
, four casters
(Figure 2)
and four screws with your wet/dry vacuum. Assemble as follows:
1. With cord disconnected from receptacle and tank cover removed, turn tank upside down so that bottom is facing up.
2. With front of tank facing you, take caster feet marked with the letter A
(Figure 3)
and place in slots on left front and right rear of tank also
marked with the letter A
(Figure 4)
. Secure with screws provided
(Figure 5)
.
3. Take caster feet marked with the letter B
(Figure 6)
and place in slots on right front and left rear of tank also marked with the letter B
(Figure 7)
. Secure with screws provided
(Figure 8).
4. If flat washers are included in hardware package place flat washer over stem of caster before installing casters into feet.
NOTE:
Flat washers
are not required with all units.
5. Insert casters into feet by placing stem of caster into holes provided. Apply pressure and twisting motion until casters snap into place
(Figure 9)
. Return tank to upright position.
A
A
A
A
A
A
B
B
B
B
B
B
B
A
A
1
2
3
4
5
6
7
8
9
