Shinybow USA SB-5544LCM Instruction Manual Download Page 8

BACK PANEL

BACK PANEL

CONNECTING THE HARDWARE

Please study the panel drawings below and become familiar with the signal input-output, Power requirements plus any controls present. 
Before using the switcher, please take the time to make certain that the device you wish to connect to its inputs is functioning properly in 
all respects. Verify that the video and audio signals are present and are being displayed properly on a suitable device. 
If all is well connect the appropriate cables between the output of the device you wish to distribute to output(s) of the switcher to the 
carious devices you wish to feed a signal to. Lastly, connect the AC to DC adaptor, connect the DC connector to the switcher fi rst and then 
plug the adaptor into a functional AC outlet.

6

1. DC POWER INLET:

 

The Switcher is fi tted with a DC power plug-park input connector. 
Please ensure that the plug-park used is of an approved type and 
is of suffi cient current carrying capacity with the correct voltage 
and connector polarity. 12Volt DC power supply 2A Max.

2. IR EXTENDER CONTROL

Support one of IR Extender (IR input)
Extend distance maximum 300 M / 1000 ft

Note: DO NOT install or remote any connections while the 
power is ON.

3. RS-232 CONNECTION:

 

RS-232 control port to allow for interfacing to a PC, such as a 
computer or touch panel control, to the switcher via this DB-9pin 
Female connector for serial RS-232 control.  

4. INPUTS-1~4 COMPOSITE/AUDIO(AR/AL):

 

Connect a signal source of Composite Video and Stereo Audio 
(AR/AL) devise to 4x4 matrix switcher.

Input 1~4 port source signals:

 Composite Video/Stereo Audio, 

3x RCA Connectors

5. OUTPUTS: 1~4 COMPOSITE/AUDIO(AR/AL):

 

Connect a signal of Composite Video and Stereo Audio (AR/
AL) direct to Female RCA connector. This connector supports 
Composite Video and Stereo Audio display device. 

Output 1~4 display port signals:

 Composite Video and Stereo 

Audio, 3x RCA Connectors

Power Jack:

DC Jack - Inner OD Ø 2.1 mm (+)
                Outside OD Ø 5.5mm (GND)
Power input -12VDC, 2A

IR Extender Jack: 

Female Jack - inner OD Ø 3.5 mm

 

Remote Port: 

DB-9pin Female connector

Composite Video Audio Via 3x RCAs

Note: With 3x RCA female connectors.

Composite Video Audio Via 3x RCAs

Note: With 3x RCA female connectors.

Summary of Contents for SB-5544LCM

















Reviews: