Shindaiwa T344 Owner'S Manual Download Page 8 | Manualshive

Page: 8 / 28

background image

8

Throttle lever free play

4-6 mm

(3/16”-1/4”)

Throttle Free Play

Adjust throttle lever free play

The throttle lever free play should be approximately 4 - 6 mm (3/16” -

1/4”). Make sure that the throttle lever operates smoothly without binding.

If it becomes necessary to adjust the lever free play, follow the procedures

and illustrations that follow.

Remove air cleaner cover

1. Loosen the air cleaner cover knob(s) and remove the air cleaner cover.
2. Turn the cable adjuster in or out as required to obtain proper free play

4 - 6 mm (3/16 - 7/4”).

3. Reinstall the air cleaner cover.

Front handle installation

NOTE:

Label shows minimum spacing for front handle location.

1. Position front handle for comfortable operation and secure screw.

Cable

Adjuster

Screw

Outer

Tube

Handle

WARNING!

Alternative fuels, such as E15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting Shindaiwa

requirements are NOT approved for use in Shindaiwa gasoline engines.

Use of alternative fuels may cause

performance problems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including,

but not limited to, improper clutch engagement. Alternative fuels may also cause premature deterioration of fuel

lines, gaskets, carburetors and other engine components.

Fuel Requirements

Gasoline -

Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain

up to 10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood

alcohol) is

NOT

approved.

Mixing Fuel

«
...
6
7
8
9
10
...
»

Summary of Contents for T344





























Reviews:

No comments

Related manuals for T344

Brand: FLORABEST Pages: 54

Brand: LawnMaster Pages: 19

Brand: Nakayama Pages: 26

Brand: EINHELL Pages: 48

Brand: Yard-Man Pages: 104

Brand: Greencut Pages: 60

Brand: Felisatti Pages: 26

Brand: Komatsu Pages: 36

Brand: Cramer Pages: 144

Brand: AEG Pages: 28

Brand: AEG Pages: 24

Atlas Copco HS 40

Brand: AEG Pages: 68

Brand: FLORABEST Pages: 136

Brand: Verdemax Pages: 24

Decora Mural MDE03-1

Brand: Leviton Pages: 2

Brand: TOOLCRAFT Pages: 60

Brand: Weed Eater Pages: 11

Domitech PA-100

Brand: Z-Wave Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands