Shindaiwa 78702 Owner'S/Operator'S Manual Download Page 13

Page: 13 / 16

ADDITIONAL PROBLEMS

Symptom

Possible Cause

Remedy

Troubleshooting Guide

Engine idle too high.

Broken clutch spring or worn clutch

spring boss.

Warped or damaged attachment.

Loose gearcase.

Chain rotates at idle

speed.

Excessive vibration.

Chain will not rotate.

Adjust idle. Check Specifi cations page for correct idle

speed.
Replace spring/shoes as required, check idle speed.

Inspect and replace attachment as

required.
Tighten gearcase securely.

Bent main shaft/worn or damaged bushings.

Shaft not installed in powerhead or gearcase.

Broken shaft.
Damaged gearcase.

Inspect and replace as necessary.

Inspect and reinstall as required.

Consult with an authorized Shindaiwa servicing

dealer.

Consult with an authorized servicing dealer.

Excessive vibration.

Chain rotates at idle speed.

Broken clutch spring or worn clutch spring boss

Warped or damaged sprocket, chain, or bar.

Bent crankshaft.

Replace spring/shoes as required, check idle

speed. Set idle: 2,750(±250) min

-1

Inspect and replace chain components as required.

Engine idle too high.

Summary of Contents for 78702

















Search results

Summary of Contents for 78702

Reviews:

Related manuals for 78702

Brands by name

Popular brands

Shindaiwa 78702, Owner'S/Operator'S Manual

Search results

Summary of Contents for 78702

Reviews:

Related manuals for 78702

Brands by name

Popular brands