Shield SNA285-125 Installation & Service Manual Download | Manualshive

Page: 73 / 76

background image

73

13

Troubleshooting

(continued)

Gas valve adjustment procedure

If adjustment of the gas valve is deemed necessary, use the
following procedures: (

Note:

The procedures below are

model specific.)

Models SNR150-100 -- SNA285-125

Locate the throttle adjustment screw on the side of the
venturi valve (FIG. 13-2). Using a screwdriver, turn the screw
a 1/4 turn

clockwise

to decrease CO

2

levels or a 1/4 turn

counterclockwise

to increase CO

2

levels. After performing

one adjustment on the valve, follow the Combustion Analysis
Procedure on page 72 of this manual to measure the
combustion.

If combustion is still not within the specified range, repeat
the procedure. This procedure SHOULD NOT be performed
more than four (4) times. If after four (4) adjustments and
the combustion is still not within the specified range, revisit
the possible causes in Table 13F on page 72 or replace the gas
valve.

THROTTLE

ADJUSTMENT

SCREW

Figure 13-2

Gas Valve Adjustment: Models

SNR150-100 -- SNA285-125

THROTTLE

ADJUSTMENT

SCREW

Figure 13-4

Gas Valve Adjustment: Model SNA500-125

Model SNA400-125

Locate the throttle adjustment screw on the top of the gas
valve, see FIG. 13-3. Using a screwdriver, turn the screw 1/8
turn

counterclockwise

to increase CO

2

levels or 1/8 turn

clockwise

to decrease CO

2

levels. After one adjustment on

the valve, follow the Combustion Analysis Procedure on page
72 of this manual to measure the combustion.

If combustion is still not within the specified range, repeat the
procedure. This procedure SHOULD NOT be performed
more than four (4) times. If after four (4) adjustments and
the combustion is still not within the specified range, revisit
the possible causes in Table 13F on page 72 or replace the gas
valve.

Model SNA500-125

Locate the throttle adjustment screw on top of the gas valve, see
FIG. 13-4. Using a screwdriver, turn the screw a 1/4 turn

counterclockwise

to increase CO

2

levels or a 1/4 turn

clockwise

to decrease CO

2

levels. After one adjustment on the valve,

follow the Combustion Analysis Procedure on page 72 of this
manual to measure the combustion.

If combustion is still not within the specified range, repeat the
procedure. This procedure SHOULD NOT be performed more
than four (4) times. If after four (4) adjustments and the
combustion is still not within the specified range, revisit the
possible causes in Table 13F on page 72 or replace the gas valve.

THROTTLE

ADJUSTMENT

SCREW

Figure 13-3

Gas Valve Adjustment: Model SNA400-125

Installation & Service Manual

TM

«
...
71
72
73
74
75
...
»

Summary of Contents for SNA285-125













































































Reviews:

No comments

Related manuals for SNA285-125

Brand: Marta Pages: 12

STELLAR BLACK PH7056

Brand: Gasmate Pages: 8

Brand: Jata calor Pages: 24

Brand: JBL Pages: 12

Brand: Cantherm Pages: 11

Brand: Rasonic Pages: 8

BLACKLIGHT 7815

Brand: MO-EL Pages: 12

POWERplus POWX1700

Brand: VARO Pages: 10

Brand: Leader Pumps Pages: 8

Brand: Quality Water Treatment Pages: 9

Brand: Ocean Technologies Pages: 2

Comfort 5000/5 LCD

Brand: Gardena Pages: 13

Brand: EBARA Pages: 172

Brand: Waterax Pages: 6

Brand: Frico Pages: 29

Brand: Zibro Pages: 24

Brand: Lasko Pages: 4

Brand: Ice-O-Matic Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands