background image

5

NEC (National Electrical Code)

Standards

A Note for the Cable Television (CATV) Installer

This reminder is to call the CATV system installer’s attention
to Article 820-40 of the NEC that provides guidelines for
proper grounding and in particular, specifies that the cable
ground  shall be connected to the grounding system of the
building as close to the point of cable entry as practical.

Antenna Grounding Outside the House

If an outside antenna is connected to the receiver, be sure the
antenna system is grounded so as to provide some protection
against voltage surges and built-up static charges. Article 810
of the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the lead-in
wire to an antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode. See
diagram below.

Unpacking the PT-7020A

The Sherbourn PT-7020A Pre/Pro should reach you in flawless
condition. If you notice any shipping damage or other issues
upon unpacking the unit, please contact your Sherbourn
Retailer immediately.

Gently lift out the unit and remove all the packing material
and accessories. It is important to save all the packing
materials and the box in case your Sherbourn PT-7020A
ever needs to be moved or shipped back to the factory for
service.

Make sure that you keep your sales receipt. It is the only
way for Sherbourn to establish the duration of your Limited
Warranty and it may be useful for insurance purposes.

Please take a moment to fill out and mail the Sherbourn
Customer Response card.

Recording the Serial Number

Please read the serial number located on the rear panel and
record it below. Also record the place where you purchased
this product and the date of purchase.

Model Number 

         PT-7020A

Serial Number ___________________________________

Place of Purchase _________________________________

Date of Purchase _________________________________

Cable TV Coaxial Cable, Satellite Dish Cables, and
Television Antennas should be grounded BEFORE the
point of entry into the house.

Always observe proper antenna or satellite dish grounding
techniques. When lightning strikes, there is always the
possibility that your antenna or dish (mounted high on the
roof) can become a conduit for lightning and electrically
damage any equipment to which it’s connected.
Additionally, proper grounding offers safety to the people
using the audio/video system in the event of an electrical
problem.

Summary of Contents for PT-7020A








































Reviews: