ShenZhen Yuejiang Technology Dobot Magician User Manual Download Page 31

Page: 31 / 153

Dobot Magician User Guide

Dobot Magician Homing Operation

Issue V1.9.0 (2020-07-23)

User Guide

Interface Description

Interface Board

The interfaces of Dobot Magician are located on the back of the base and the Forearm

respectively. Figure 4.1 shows the interfaces on the back of the base, and Table 4.1 lists the

description.

Figure 4.1 Interfaces in the base

Table 4.1 Interface Description

No.

Description

Reset key: Reset MCU program

During resetting, the LED indicator on the base turns yellow. About 5 seconds

later, if the LED indicator turns green, it indicates that the reset is successful

Functional key:



Short press: Start running offline program



Long press for 2 seconds: Starting homing procedure

Communication interface/UART interface: Connect with Bluetooth, WIFI and

so on

The Dobot protocol is adopted.

USB interface: Connect with PC

Power interface: Connect with power adaptor

Peripheral interface: Connect with air pump, extruder, sensor and other

peripheral equipment. For details about peripheral interfaces, please see Table

4.2

Table 4.2 lists the peripheral interface description.

Summary of Contents for Dobot Magician


























































































































































Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands

ShenZhen Yuejiang Technology Dobot Magician, User Manual

Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands