manualshive.com logo in svg

Shenzhen Roundwhale Technology Co., LTD. R-C1, Instruction Manual, Page: 29 / 40

Share
Download
Shenzhen Roundwhale Technology Co., LTD. R-C1 Instruction Manual Download Page 29

29

8.1.3 The COMBO stimulator is sensitive to heat and may 

not be exposed to direct sunlight. And do not place it 

on hot surfaces. 

8.1.4 Clean the surface of the electrode pads carefully with 

a damp cloth. Make sure the device is turn off! 

8.1.5 For reasons of hygiene, each user should use his/her 

own set of electrodes. 

8.1.6 Do not use any chemical cleaners or abrasive agents 

for cleaning. 

8.1.7 Ensure that no water penetrates into the machine. 

Should this happen, use the device again only when it 

is completely dry. 

8.1.8 Do not clean the device during treatment. Be sure that 

the device is turned off and the battery is unloaded 

before cleaning.

8.2 Maintenance

8.2.1 The manufacturer didn’t authorize any maintenance 

agencies abroad. If your device has any problem, 

please contact the distributor. The manufacturer will 

not be responsible for the results of maintenance or 

repairs by unauthorized persons. 

8.3.2 The user must not attempt any repairs to the device or 

any of its accessories. Please contact the retailer for 

repair.   

8.3.3 Opening of the equipment by unauthorized agencies 

is not allowed and will terminate any claim to warran-

ty.

Each product in manufacturing has been through the sys-

tematic validation. The performance is stable and does not 

need to undertake calibration and validation.

If your product can’t reach the expected performance and 

the basic function has changes in normal use, please con-

tact the retailer.

Summary of Contents for R-C1









































Reviews:

No comments