background image

Page 5

STEP 7: SECURE BASE FEET
Fig. 7

Fig. 7

STEP 8: INSTALL AUGER ANCHORS
Fig. 8

Fig. 8

Side View

Inside View

STEP 9: END PANEL INSTALLATION
Fig. 9A, 9B & 9C

Fig. 9A

Fig. 9B

Depending on the model you have purchased, your base feet will either

fit onto the outside of the leg pole or slide into the bottom of the leg pole.

After installing the base feet line up the holes in the leg to the holes in

the feet and secure with the hardware indicated in Fig. 7.

Using a ¾” pipe or steel rod (a car tire iron works also) placed 

through the eyelet of the auger; screw the anchor into the ground.  

Start at the corners of the shelter and space the remaining anchors 

evenly along the length of the shelter.  Screw the anchor into the 

ground until the eyelet is sticking out of the ground by 1-2” so it can 

be anchored to the legs.  Wrap the cable provided through the 

eyelet of the anchor and around the frame as indicated in Fig. 8.   

Secure the cable with the clamp(s) provided.

Hold the end panel at the top center with the white inner

surface facing the inside of the shelter (if you have a

white shelter the inner surface has the visible weld seams).

Carefully remove the top rail from the top bend and place

the webbing in between the two.  The top rail should pass

through the loop of the webbing.  Replace the top rail onto

the top bend and secure it with the hardware indicated

in Fig. 9A, 9B.

Remove the nut from the side rail and carefully pull the

side rail away from the ShelterLock (the rail only needs to

be pulled away enough to pass the webbing through the

connection). 

 If this connection has the wind brace on it

remove the wind brace end before pulling the side rail.

When the webbing is through replace the side rail, and the

cross rail if necessary Fig 9C.  Replace the nut and tighten. 

Repeat this for the other side.

Locate where the webbing exits the pocket on each side of

the end panel.  Pull the webbing carefully to remove the slack

from the end panel.  Be careful not to pull the webbing through

the other side of the panel. Install the “S”-hook from the

ratchet into the leg of the shelter Fig 9D.  Insert the webbing

into the spindle of the ratchet and pull tight.  Wind the ratchet

enough so that the webbing overlaps itself.  Repeat the

process on the other side of the panel. Position the end panel

so that it is centered on the building.  Tighten the ratchets,

alternating from one side to the other, until the end panel is

tight.  Repeat these steps on the other end of the building. 

Fig. 9C

Fig. 9D

Summary of Contents for 12'W x10'H Peak Style








Reviews: